Craftsman 320.17541 operating instructions General, Routine Maintenance

Page 30

WARNING: To

ensure safety

and reliability,

all repairs should

be performed

]

I by a qualified service

technician at

a Sears Service

Center.

 

GENERAL

Only the parts shown on the parts list are intended for repair or replacement by the customer. All other parts represent an important part of the double insulation system and should be serviced only be a qualified Sears@ service technician,.

A WARNING: For your safety, ALWAYS turn off switch and unplug router motor from the power source before performing any maintenance or cleaning.

tthas been found that electric tools are subject to accelerated wear and possible

premature failure when they are used to work on fiber glass boats and sports cars, wallboard, spackling compounds or plaster.. The chips and grindings from these materials

are highly abrasive to electrical toot pads, such as bearings, brushes, commutators, etco

Consequently, it is not recommended that this tool be used for extended work on any fiberglass material, wallboard, spackling compound or plaster. During any use on these materials, it is extremely important that the tool is cleaned frequently by blowing with an air jeL

during power tool operations, or when blowing dust. If operation is dusty, also

A WARNING: Always wear safety goggles or safety glasses with side shields wear a dust mask.

ROUTINE MAINTENANCE

products, penetrating oils, etc. come in contact with plastic parts. Chemicals can l Z_ WARNING: DO NOT at any time let brake fluids, gasoline, petroleum-based

damage, weaken or destroy plastic, which may result in serious personal injury.

1.When work has been completed, clean the tool to allow smooth functioning of the tool over time.

2.Use clean damp cloths to wipe the tool.

3.Check the state of all electrical cables°

4o Keep the motor air openings free from oil, grease and sawdust or woodchips, and store tool in a dry place°

5.Be certain that all moving parts are welt lubricated, particularly after lengthy exposure to damp and/or dirty conditions°

_ WARNING: For your safety, ALWAYS turn off switch and unplug router

motor from the power source before performing any maintenance or cleaning.

Refer to Collet/Nut Care and Cutter Bits on page 16 for cleaning care.

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Warranty Hoffman Estates, IL 60179 U.S.AOneyear Fullwarranty on Craftsman Product For Free ReplacementSafety Alert Symbol IndicatesDANGER,WARNING,OR Damage Prevention and Information MessagesWork Area Safety Personal SafetyTool USE and Care Safety Electrical SafetyLabel on your tool may include the following symbols Electrical SafetySafety Symbols for Your Tool Extension CordsCutter bits coast after router is switched off Service SafetySafety Rules for Routers Do not HAND-HOLDTHE Router in AN Upside Down or HorizontalSafety Rules for Routers Some examples of these chemicals are Additional Rules for Safe OperationAdditional Rules for Safe Operation In. Collet/Nut Collet/Nut wrenchScrews For attaching Hood Sawdust Extraction HoodThis Fixed Base Router has the following features Knowyour Fixed Base Router cont. FigIndicator Light Know Your Fixed Base Router cont. FigSelecting the Cutter BIT RPMInstalling and Removing the Cutting BIT Figs , 4 and 4a Installing the Cutter BITInstalling Router Motor in Base Removing the Cutter BIT Figs and 4 seeBase Fig Removing Motor from Base see FigRious personal injury Adjusting Depth of CUT Micro AdjustmentsCoarse Adjustment To Adjust Depth Figs and 6a Do not Exceed 1/8-1N.DEPTH of CUT in a single passSoft Start Feature Deep CutsLED Worklights Fig Edge Routing or Internal Routing Edge Routing FigInternal Routing Figs , 11a, 11b Feed DirectionFreehand Routing with the Fixed Base Fig Edging with a Pilot BIT Figs and 14a 14aFeeding the Router Fig Direction of Feed External Cuts FigDirection of Feed Internal Cuts Figs and 16a Guide OutsideRate of Feed Figs and 17a Feeding TOO Fast FigChip shield deflector is not intended as a safety guard TabsDust Collection with Dust Extraction Hood Routine Maintenance GeneralReplacement of Carbon Brushes Fig LubricationDovetail 4k Warning Only use Amp / 13/4Peak HP Amp / 1314Peak HP Model Number Item No Parts No Desi crptioAmp / 1 3/4 Peak HP Fixed Base Router- Model Number Parts DescriptionPage Page USA 800-36!-6665 Canada No matter who made it, no matter who sold itSears Parts and Repair Center SU-HOGAR
Top Page Image Contents