Craftsman 315.175 owner manual Keep Hands Away from Routing Area, Never USE in AN Explosive

Page 4

IPROTECT YOUR HEARING, Wear hearing protection during extended periods of operation,

IDO NOT ABUSE CORD. Never carry tool by cord or yank it to disconnect from receptacle. Keep cord from heat, oil, and sharp edges.

•SECURE WORK. Use clamps or a vise to hold work. It is safer than using your hand and it frees both hands to operate tool.

•DO NOT OVERREACH. Keep proper footing and balance at all times. Do not use on a ladder or unstable support. Secure tools when working at elevated positions.

•MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow

instructions for lubricating and changing accesso- des.

•DISCONNECT TOOLS. When not in use, before servicing, or when changing attachments, tools should be disconnected from power supply.

•REMOVE ADJUSTING KEYS AND WRENCHES, Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on.

•AVOID ACCIDENTAL STARTING. Do not carry plugged-in tool with finger on switch. Be sure switch is off when plugging in.

•MAKE SURE YOUR EXTENSION CORD IS IN GOOD CONDITION. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. A wire gage size (A.W.G.) of at least 14 is recommended for an extension cord 100 feet or less in length. A cord exceeding 100 feet is not recommended. If in doubt, use the

next heavier gage. The smaller the gage number, the heavier the cord.

•OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords suitable for use outdoors. Outdoor approved cords are marked with the suffix W-A, for example - SJTW-A or SJOW-A.

•KEEP CUTTERS CLEAN AND SHARP. Sharp cutters minimize stalling and kickback.

•KEEP HANDS AWAY FROM ROUTING AREA.

Keep hands away from cutters. Do not reach under- neath work while cutter is rotating. Do not attempt to remove material while cutter is rotating.

•NEVER USE IN AN EXPLOSIVE

ATMOSPHERE. Normal sparking of the motor could ignite fumes.

•INSPECT TOOL CORDS PERIODICALLY and if damaged, have repaired at your nearest Sears

Repair Center. Stay constantly aware of cord

location.

•INSPECT EXTENSION CORDS

PERIODICALLY and replace if damaged.

•KEEP HANDLES DRY, CLEAN, AND FREE FROM OIL AND GREASE. Always use a clean cloth when cleaning. Never use brake fluids, gasoline, petroleum-based products, or any strong solvents to clean your tool.

•STAY ALERT AND EXERCISE CONTROL. Watch what you are doing and use common sense. Do not operate tool when you are tired. Do not rush.

•CHECK DAMAGED PARTS. Before further use of the tool, a guard or other pad that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged should be

properly repaired or replaced by an authorized service center.

•DO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF. Have defective switches replaced by an authorized service center.

•INSPECT FOR and remove all nails from lumber before routing.

•DO NOT operate this tool while under the influence of drugs, alcohol, or any medication.

•POLARIZED PLUGS. To reduce the risk of electric shock, this tool has a polarized plug (one blade is wider than the other). This plug will fit in a polar- ized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

•WHEN SERVICING USE ONLY IDENTICAL CRAFTSMAN REPLACEMENT PARTS.

•WHEN USING THIS ROUTER WITH A ROUTER

TABLE, HELP PREVENT POSSIBLE SERIOUS INJURY BY KEEPING THE CUTTER GUARDED AT ALL TIMES. Use only router tables, with guards, that have been designed for use on touters that are of this type, size, and weight.

•DO NOT USE TOOL UNDER "BROWNOUT" OR

OTHER LOW VOLTAGE CONDITIONS. Also, do not use with any device that could cause the power supply voltage to change.

•SAVE THESE INSTRUCTIONS. Refer to them frequently and use them to instruct others who may use this tool. If you loan someone this tool, loan them these instructions also.

SAVE THESE INSTRUCTIONS

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Router Full ONE Year Warranty on Craftsman Router ChargeDouble Insulation Symbol Meaning Safety AlertsymbolRead ALL Instructions Keep Hands Away from Routing Area Never USE in AN ExplosiveInspect Extension Cords Do not USE Tool Under Brownout orCollet Panel BIT STRAIGH1 Bits Cutter Bevel ChamferBIT Round Groove Chamfer Carbidetippedbits JSwitch Chip ShieldLOCK-ON Button Wrench Storage AreaINSTALLING/REMOVING Cutters See Figures 2Cuifer Wrench Collet NUT To Loosen Spindlelock To LockDepth of CUT Adjustments See Figures 4, 5,Tighten Locking Cutterat Zero Depthof CUT See FigureIndicatordepth Router TablesPractice Before Actual USE Helpful HintsProper Feeding Rate of FeedForce Feeding Depth of CUT TOO Slow FeedingWidth Routing ThrustStarting and Ending a CUT Internal Routing Edging with Pilot BitsTOP Edge Shaping Edge RoungGeneral LubricationProper Care Ofcutters Proper Care OfcolletLead Power Handle Cordwork Ught Light Bulb ReplacementSee Figures 15 Nailor PIN REDCraftsman Router Model Number Parts List Parts Direct Standard Hardware Item MAY be Purchased Locally 175000

315.175 specifications

The Craftsman 315.175 is a versatile and robust power tool that has earned a solid reputation among DIY enthusiasts and professionals alike. Designed for various woodworking tasks, this model is particularly esteemed for its exceptional performance and user-friendly features.

One of the standout attributes of the Craftsman 315.175 is its powerful motor. Engineered to deliver substantial torque, the motor ensures maximum efficiency while tackling heavy-duty tasks. This power enables the tool to perform flawlessly across a range of applications, from home improvements to intricate craft projects.

The Craftsman 315.175 is equipped with an ergonomic design, which enhances user comfort during prolonged use. Its lightweight construction allows for easy maneuverability, reducing fatigue and improving overall control. The soft-grip handle provides additional comfort and grip, making it easier to handle the tool with precision.

This model features advanced technologies that set it apart from competitors. Notably, its quick-release blade change system allows users to swap out blades swiftly and effortlessly. This technology not only saves time but also enhances safety, as users can replace blades without the need for additional tools.

The Craftsman 315.175 also includes adjustable speed settings, providing users with the flexibility to adapt to various materials and tasks. Whether cutting through hardwood or softwood, users can select the optimal speed to achieve the desired results. This adaptability makes the tool suitable for a wide range of projects, from rough cuts to detailed finishing work.

Durability is another key characteristic of the Craftsman 315.175. Constructed with high-quality materials, this tool is designed to withstand the rigors of demanding use. The robust build ensures longevity, making it a reliable choice for both casual users and professional tradespeople.

Safety features are integral to the design of the Craftsman 315.175. With an integrated safety switch and blade guard, users can operate the tool with greater peace of mind. These features minimize the risk of accidents, allowing users to focus entirely on their projects.

In summary, the Craftsman 315.175 is a powerful, versatile, and user-friendly tool that caters to a broad spectrum of woodworking needs. Its robust motor, ergonomic design, quick-release blade change system, adjustable speed settings, and safety features collectively make it a top choice for anyone seeking efficiency without compromising on safety. Whether for professional use or DIY projects, the Craftsman 315.175 stands out as a dependable and effective tool.
Top Page Image Contents