Grizzly G9983 instruction manual Machine Features, External Features Control Panel

Page 10

SECTION 4: MACHINE FEATURES

External Features

 

Control Panel

 

 

 

 

 

 

 

 

 

To help you understand the set up and operation instructions, we recommend that you become familiar with the basic features of your new sander.

Please match up the list below with the letters in Figure 2 to identify the external sander compo- nents.

A.Control Panel

B.Table Extension

C.Conveyor Height Handwheel

D.Conveyor Height Gauge

E.Dust Port

F.Load Meter

G.Emergency Stop Bar

H.Pressure Regulator

 

E

A

F

B

 

 

G

C

 

H

D

Figure 2. These are the basic external

components of the sander.

The control panel houses the main power switch, the feed belt ON/OFF buttons and the sanding belt ON/OFF buttons. Please refer to Figure 3 to identify these controls.

A.Main Power ON / Emergency STOP switch.

B.Sanding Belt OFF button.

C.Sanding Belt ON button.

D.Feed Belt OFF button.

E.Feed Belt ON button.

F.Power Indicator Light

A

 

D

 

E

 

 

 

 

 

 

 

 

 

 

B C

F

Figure 3. These are the main power controls.

 

 

 

 

 

 

 

 

-8-

 

 

G9983 15" Open-End Wide-Belt Sander

 

 

Image 10
Contents OPEN-END WIDE-BELT Sander Page Table Of Contents Safety Safety Instructions For Power ToolsLength AMP Rating 25ft 50ft 100ftAdditional Safety Instructions For The Wide-Belt Sander Introduction 220V Single-Phase Circuit RequirementsGrounding WiringExtension Cords Machine Features External Features Control PanelAccess Doors These items are behind Left-hand access doorUnpacking SET UPPiece Inventory Hardware Recognition Chart MeasureClean Up Site ConsiderationsTo install the handwheel handle Beginning AssemblyHandwheel Handle To insert the platen PlatenTo set the platen even with the belt rollers Sanding Belt To install a sanding beltAir Hose To connect the air hoseTo Tighten Belt Tension Sanding Belt Tension Pressure RollersTo Loosen Belt Tension Dust Collection Test Run Before you test run your machineRecommended Adjustments Recommended adjustment checklistChoosing Sandpaper OperationsBefore Starting Grit TypeConveyor Height Feed Belt Speed To change feed belt speeds Unplug the sanderLoad Meter Operation This is the load meterPlaten Depth Cleaning Pads Three basic platen positionsGeneral MaintenanceCleaning Sanding Belts Emptying FiltersDate Approximate Hours Of Use Maintenance Performed Service Adjustments Oscillation TimingOscillation Speed Use the knob on this valve to control Oscillation speedTo adjust the limit switches Limit SwitchesTo adjust the oscillation return Oscillation ReturnTo adjust the pressure roller depth Unplug the sander Pressure Roller DepthTo adjust the pressure roller tension Unplug the sander Pressure Roller TensionFeed Belt Tracking To adjust the feed belt tracking Unplug the sanderFeed Belt Tension To check the feed belt trackingBelt Tension Replacing V-BeltsG9983 15 Open-End Wide-Belt Sander Platen Graphite Air System To replace the graphite sheetReplacing Brakes Date Approximate Hours Of Use Service Performed Closure Machine Data Sheet Air Inlet Motor 5 6 8 9 10 11 14 Model G9983 Wiring Diagram 220 Volt Single Phase G9983 Parts Breakdown Platen Tool109108 124 111 110 112 Machine Base Roller Bracket LH G9983 Contact Roller Base 414 Machine Frame 621 622 620 601 619 623 Control BOX Troubleshooting Symptom Possible Cause Corrective ActionTion Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC Page Call Today For a Free Full Color Catalog