Jet Tools 22-44 Pro operating instructions Leveling the Sander, Dust Collection

Page 11

6.Position the table (H, Figure 9) over the brackets, and install four 1/4”x3/4” square neck bolts (J), 1/4” flat washers (K), and 1/4” hex nuts (L). Do not fully tighten yet.

7.The table should be positioned even with or slightly below the conveyor belt surface. To check position, place a level or straight edge near the left side of the conveyor and extending out over the table, as shown in Figure 10. Raise the conveyor table until the drum holds the straight edge in place, and

adjust the infeed table until it is even with or

Figure 10

slightly below the conveyor belt surface.

 

8.Place the straight edge near the the right side of the conveyor table and repeat. Tighten all hex nuts on the infeed table.

9.Mount the outfeed table in the same manner as described above. (Removal of existing screws on the rails will not be necessary for the outfeed side.)

Leveling the Sander

Proper leveling is important for getting the maximum performance from your sander. Before making fine adjustments, place the unit where it will be used in the shop. Then adjust the four leg glides (see Figure 4) using a carpenter’s level placed on the conveyor bed in both X- and Y-axis positions. Make sure the hex nuts on the leg glides are tightened securely against the sander legs.

If you are using the optional casters, level the sander after positioning the machine where it will be used most often. Place washers on the casters as needed to shim up the legs. Mark the position of the legs on the floor with tape so the sander can be returned to the same position.

Dust Collection

Dust collection is mandatory for a safe work environment and extended abrasive life. The sander is equipped with a 4” dust collection port at the back of the dust cover. It is designed to be used with standard 4” dust collection hose connected to a high volume dust collector with a minimum capacity of 600 CFM.

Using a shop vacuum is not recommended for this machine, but if used it should be a 16 gallon or larger canister type shop vacuum. This requires converting the dust port down to 2-1/2”. An adapter is available from your dealer (stock no. 80-2910) for converting to the 2-1/2” hose. Do not reduce hose size smaller than 2-1/2”. For best results, follow recommendations of the dust collector manufacturer.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Drum Sander Warranty and Service Table of Contents Page Page 44 2 passes Introduction SpecificationsFeatures and Terminology Unpacking Contents of the Shipping ContainerTable Support Screws AssemblyInstall Stand Legs Infeed and Outfeed Tables Optional Install HandwheelInstall Conveyor Table Dust Collection Leveling the SanderInstalling Abrasives Page Grounding Instructions Dust Cover AdjustmentsSwitch Lockout Extension CordsPage Drum Alignment Depth Gauge CalibrationInitial Drum Alignment Conveyor Belt Tension and Tracking Trackers Conveyor Belt ReplacementAdjusting Table Supports Tension Roller AdjustmentRotating Drum Bearings Replacing V-BeltReplacing Drum Bearings Operation Dust Collection Keeping the Machine Clean MaintenanceUnderside of conveyor shown Tracker KitAbrasive Selection Guide AbrasivesTroubleshooting Motor and Electrical Problems Trouble Troubleshooting Operational Problems Trouble Probable Cause Remedy Replacement Parts Optional AccessoriesStand Assembly Index No. Part No Description Size Qty Parts List Stand AssemblyDrum Head Assembly Parts List Drum Head Assembly Conveyor and Motor Assembly Parts List Conveyor and Motor Assembly Infeed and Outfeed Tables 98-2201 Optional Accessory Electrical Connections Page Page WMH Tool Group

22-44 Pro specifications

The Jet Tools 22-44 Pro drum sander stands out as one of the leading machines in the woodworking industry, known for its exceptional performance and durability. Aimed at both professional woodworkers and serious hobbyists, this tool boasts a range of features that enhance efficiency and precision, making it a valuable addition to any workshop.

One of the primary features of the Jet 22-44 Pro is its powerful 1.75 HP motor. This motor ensures consistent and reliable operation, allowing users to tackle a variety of sanding tasks with ease. The machine operates at 1,800 RPM, providing quick and efficient material removal. The adjustable table height allows for a maximum sanding width of 22 inches, accommodating larger workpieces for versatility in projects.

In terms of technology, the Jet 22-44 Pro employs a unique, patented drum design that ensures even sanding across the entire surface. This design minimizes the risk of snipe, a common problem in sanders that can result in uneven finish on workpieces. The 44-inch long sanding drum provides ample surface area, which aids in achieving a flawless finish without the need for excessive passes.

The tool features an adjustable infeed and outfeed table, ensuring optimal material support and stability during sanding operations. This feature is particularly beneficial for larger boards, as it prevents warping and allows for more accurate sanding. Additionally, the integrated dust collection system enhances cleanliness by efficiently capturing dust and debris, promoting a healthier working environment.

The Jet 22-44 Pro is equipped with a micro-adjustable sanding drum, allowing users to make precise depth adjustments for different applications. This functionality makes it easy to switch between various grits without sacrificing accuracy. Furthermore, the machine’s sturdy construction and robust frame reduce vibration during operation, contributing to improved accuracy and reduced fatigue during prolonged use.

The user-friendly design of the Jet 22-44 Pro also includes safety features such as an emergency stop button and integrated overload protection. This ensures that the machine can be operated safely, with features in place to prevent damage to both the tool and the user.

In summary, the Jet Tools 22-44 Pro drum sander combines power, versatility, and advanced technology to deliver an outstanding finishing tool for woodworkers. Its robust motor, unique drum design, and user-friendly features make it a top choice for anyone looking to enhance their woodworking capabilities.
Top Page Image Contents