Model 687 | - 01 | ||
www.dremel.com | |||
Modèle | 687 | - 01 | |
PO Box 1468 Racine, WI |
|
|
|
| Modelo | 687 | - 01 |
Wear eye protection. Maximum operating |
speed 35,000/rpm. |
For more information, refer to your rotary tool Owner’s Manual.
MANDRELS: PART # 401, 402
•Mandrels are shanks with a threaded screw head used for polishing accessories,
2.125 |
POLISHING ACCESSORIES: PART # 414, 429
•Use to polish most metals and plastics.
•When polishing precious metals (gold and silver), use the felt accessories and polishing compound (jewelers rouge) with a very light touch.
CUT-OFF WHEELS: PART # 409, 426
!
WARNING Read and understand tool manual. Wear eye and respiratory protection. Always grip tool firmly with both hands. Kickback can occur at any time caus- ing loss of control and injury.
Cut Off
Hanging Tab
Remove
Accessories
and Tray
L E M E R D
Remove Pin, then Insert Dividers
to store Accessories
L E M E R D
size 7” x | final size |
| - |
•Use to cut or slot bolts, screws, wire closet organizers, metal, thin wood and plastic.
•
•
BRISTLE BRUSH: PART # 403
!
WARNING Read and understand tool manual. Wear eye and respiratory protection. Allow brushes to run at 15,000/rpm for one minute before use. Brush with tips and apply only light pressure in use. Do not stand in front of or in line with brush.
•Do not use wire brushes at speeds greater than 15,000/rpm.
•Small, versatile brushes efficiently remove rust and cor- rosion, and polish metal surfaces.
•Use bristle brushes for cleaning and polishing silverware, jewelry and metal surfaces.
SANDING ACCESSORIES: PART # 407, 408, 432
•Ideal for shaping and smoothing wood and fiberglass.
•Start with coarse bands/disks and finish with finer grits.
•Most effective when using a light touch.
HIGH SPEED CUTTER: PART # 194
•Use for shaping and hollowing most soft metals, plastics and woods.
•Cutting is done with the sides of the cutter. The point or tip of the cutter cuts poorly and chatters.
ALUMINUM OXIDE GRINDING STONE: PART # 952
•Excellent for removing flashing from metal castings, smoothing welded joints, grinding off rivets and for any job that requires grinding. Also great for rust removal and deburring.
SILICON CARBIDE GRINDING STONES: PART # 84922, 85422
•These stones are designed to work well on hard materi- als such as stone, glass, ceramics and hardened mate- rials.
d'exploitation : 35 000 tr/min.
Pour plus d'informations, consultez le manuel d'utilisa- tion de votre outil rotatif.
ACCESSOIRES DE POLISSAGE : NO DE RÉF. 414, 429
•Polissent la plupart des métaux et des plastiques.
•Lorsque vous polissez des métaux précieux (or et argent), utilisez les accessoires en feutre et la pâte à polir (oxyde ferrique) en procédant sans trop appuyer.
FRAISES CIRCULAIRES : NO DE RÉF. 409, 426
!ADVERTENCIA Lisez et comprenez le contenu du manuel de l'outil.
•Pour couper ou fendre des boulons, des vis, des paniers de rangement métalliques, du métal, du bois fin et du plastique.
•Les fraises circulaires coupent seulement le long des bords. Appuyez légèrement et tenez l'outil rotatif des deux mains pour maintenir l'alignement.
•Les fraises circulaires sont cassantes. N'essayez pas de poncer ou de tailler des trous incurvés avec ces fraises.
BROSSE À SOIES : NO DE RÉF. 403
!ADVERTENCIA Lisez et comprenez le contenu du manuel de l'outil.
•N'utilisez pas les brosses métalliques à plus de 15 000 tr/min.
•Les petites brosses polyvalentes éliminent efficacement la rouille et la corrosion et font briller les surfaces métalliques.
x 7” (folded | short way |
for final size of | and then 2 times the |
Printer trims here | once the long way |
| Fold |
2610920479