Schumacher SCF-10000A owner manual Using the BUILT-IN Battery Tester

Page 10

USING THE BUILT-IN BATTERY TESTER

OVERVIEW

This battery charger has a built-in battery tester that displays either an accurate battery voltage or an estimate of the battery’s relative charge based on the battery voltage and the Battery Council International scale.

TESTING SEQUENCE

There are four basic steps required to use the 10000A as a battery tester.

1.Connect the charger battery clamps to the battery. Be sure to follow all of the precautions listed under “OPERATING INSTRUCTIONS”.

2.Connect the charger power cord to a 120 VAC outlet. Again, be sure to follow all of the precautions listed under “OP-

ERATING INSTRUCTIONS”.

3.If necessary, press the Battery Type button until the correct type is indi- cated.

4.Read the voltage on the digital LED or press the display mode button to set the tester to “Battery %” and read the battery percent.

TESTER AND CHARGER When first turned on, the 10000A operates only as a tester, not as a charger. To continue to use it as only a tester, avoid pressing the CHARGE RATE switch button. Selecting a charge rate activates the battery charger and deactivates the tester.

POWER-UP IDLE TIME LIMIT

If no switch button is pressed within ten minutes after the unit is first powered up, the unit will automatically switch from tester to charger, if a battery is connected. In that case, the unit will be set for the 2A charge rate and 12V REGULAR battery type.

TESTER WITHOUT TIME LIMIT

If either the DISPLAY MODE or BAT- TERY TYPE button is pressed within the first ten minutes after the unit is powered up, the unit will remain a tester (not a charger) indefinitely, unless a charge rate is selected.

TESTING AFTER CHARGING

After the unit has been changed from tester to charger (by selecting a charge rate), it remains a charger as long as it has power. Disconnect and reconnect the power to change the unit back to a tester.

TESTER STATUS LEDs

When the 10000A is operating as a battery tester, the status LEDs light under the following conditions.

•The CHARGED (green) LED will light if a charged battery is tested.

•The CHARGING (yellow) LED does not light in the battery test mode.

•The CHECK (red) LED lights unless a properly connected battery is de- tected.

•When the tester display mode is set to voltage, none of the Status LEDs light.

INITIAL PERCENT CALCULATION

When a battery % is calculated for the first time after connecting a battery, the digital LED will show two dashes (“--”) for a period as long as several seconds while the tester analyzes the battery.

NOTES FOR TESTING BATTERY % A recently charged battery could have a temporarily high voltage due to what is known as “surface charge”. The voltage of such a battery will gradually drop during the period immediately after the charging system is disengaged. Consequently, the tester could display inconsistent values for such a battery. For a more accurate reading, the surface charge should be removed by temporarily creating a load on the battery, such as by turning on lights or other accessories.

The battery % ranges from 0 to 100.

The battery tester is only designed to test batteries. Testing a device with a rapidly changing voltage could yield unexpected or inaccurate results.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Send Warranty Product Repairs to Table of Contents Important Safety Instructions Help US Help YOUPersonal Safety Precautions Using AN Extension Cord Before Using Your Battery ChargerPreparing Your Battery to be Charged Plugging ITOperating Instructions Charging Battery in the VehicleNegative Grounded System Charging Battery Removed from the Vehicle Using Engine StartBattery Type Switch SCF-10000A Control Panel Display Mode SwitchCharge Rate Switch Charger ControlControl Panel Guide Mode of OperationDigital Display Using the BUILT-IN Battery Tester Starting Sequence Using Your Engine StarterEngine Starting Notes Using Your Battery Charger Charging Tips Battery Percent and Charge Time Troubleshooting Problem Possible Cause SolutionMaintenance and Care Limited WarrantyManuel d’utilisation Faire parvenir les produits à réparer sous garantie àTable DES Matières Conservez CES Instructions Consignes DE Sécurité ImportantesAIDEZ-NOUS À Vous Aider N’oubliez pas Mesures DE Sécurité Personnelles Branchement Avant D’UTILISER LE Chargeur DE BatteriePréparer LA Batterie Pour LA Charge Utilisation D’UNE RallongeCircuit À Masse Négative Consignes D’UTILISATIONCharge DE LA Batterie Dans LE Compartiment Moteur Branchement à un circuit à masseCharge DE LA Batterie Hors DU Véhicule Circuit DE Démarrage ’URGENCECommutateur DE Taux DE Charge Tableau DE Commande DU ChargeurCommutateur DE Type DE Batterie Guide Tableau DE Commande Tableau DE Commande DU Modèle SCF-10000AUtilisation DU Testeur DE Batterie Intégré Page Séquence DE Démarrage Utilisation DU Circuit DE Démarrage D’URGENCEDémarrage D’URGENCE Utilisation DU Chargeur DE Batterie Conseils Pour LA ChargePourcentage ET Temps DE Charge Compléter un cycle de charge interrompu si leTableau DE Dépannage Anomalie Cause Probable CorrectifEntretien Garantie Limitée

SCF-10000A specifications

The Schumacher SCF-10000A is a prominent jump starter and power bank that has gained immense popularity among automotive enthusiasts and everyday drivers alike. This device is specifically designed to provide a reliable and efficient solution for jump-starting vehicles and powering various electronic devices. With a robust set of features and advanced technologies, it stands out in a crowded market.

One of the main features of the SCF-10000A is its impressive jump-starting capability. This compact unit can deliver a peak current of up to 10,000 amps, making it suitable for starting a wide range of vehicles, including cars, trucks, motorcycles, and even boats. The device is equipped with heavy-duty jumper cables that ensure a secure connection and prevent any accidental sparks, enhancing user safety during operation.

In addition to its jump-starting abilities, the Schumacher SCF-10000A functions as a multi-purpose power bank. It comes with multiple USB ports, allowing users to charge smartphones, tablets, and other devices while on the go. This feature adds a layer of convenience, making it an ideal companion for road trips, outdoor adventures, or emergency situations.

Durability and reliability are essential characteristics of the SCF-10000A. The unit is housed in a rugged, impact-resistant casing that is designed to withstand harsh conditions, ensuring longevity. Additionally, the device features an integrated LED flashlight with multiple modes, including SOS and strobe, which can be a lifesaver during emergencies or low-light situations.

Technologically, the SCF-10000A incorporates smart charging technology that automatically detects the power requirements of connected devices. This ensures optimal charging efficiency and protects against overcharging, overheating, and short circuits. The built-in LCD screen provides real-time information on battery status, output voltage, and charging progress, giving users valuable insights into the device's performance.

The Schumacher SCF-10000A is also engineered with safety features, including reverse polarity protection, ensuring that incorrect jumper cable connections do not cause damage to the vehicle or the unit itself. With these considerations in mind, this powerful jump starter and power bank provide an unmatched combination of performance, convenience, and safety, making it an essential tool for any driver.
Top Page Image Contents