Schumacher SCF-10000A owner manual Using Your Battery Charger

Page 12

USING YOUR BATTERY CHARGER

OVERVIEW

Using this battery charger is very simple. First, connect the battery and AC power following the precautions listed under “OPERATING INSTRUC- TIONS”. Then select the appropriate BATTERY TYPE and CHARGE RATE for your battery. The charger will then do everything automatically. This section explains a few details.

CHARGING: If the charger does not detect a properly connected battery, the CHECK (red) LED will light continuously until such a battery is detected. Charg- ing will not begin while the CHECK light is on. When charging begins, the CHARGING LED will be lit.

AUTOMATIC SHUT OFF: When the 2A, 15A or 40A charge rate is selected, the charger is set to perform an automatic charge. When an automatic charge is performed, the charger stops charging automatically after the battery is charged.

ABORTED CHARGE: If charging can’t be completed normally, charging will be aborted. When charging is aborted, the charger’s output is shut off and the red CHECK LED and digital LED blink on and off (at opposite times). In that state, the charger ignores all buttons. To reset from after an aborted charge, either disconnect the battery or unplug the charger.

DESULFATION MODE: If a battery is left discharged for an extended period, it could become sulfated and not accept a normal charge. If the charger detects a sulfated battery, the charger will switch to a special mode of operation designed for such batteries. Activation of the spe- cial desulfation mode is indicated by blinking the CHARGING LED. If suc- cessful, normal charging will resume af- ter the battery is desulfated. The CHARGING LED will then stop blinking

and light continuously. Desulfation could take up to 10 hours. If desulfation fails, charging will be aborted and the CHECK (red) LED will blink.

COMPLETION OF CHARGING: Charge completion is indicated by the CHARGED (green) LED; when lit, the charger has stopped charging and switched to the Maintain Mode of operation.

MAINTAIN MODE: When the CHARGED (green) LED is lit, the charger has started Maintain Mode. This mode of operation is also known as Float-Mode Monitoring. In this mode, the charger keeps the battery fully charged by delivering a small current, when necessary. The voltage is main- tained at a level determined by the BATTERY TYPE selected.

GENERAL CHARGING NOTES: The unit is designed to control its cooling fan for efficient operation.

Consequently, it is normal for the fan to start and stop when maintaining a fully charged battery. The fan does not run in Tester Mode.

If the charge mode is changed after charging has started (by pressing the CHARGE RATE or BATTERY TYPE button), the charging process will be restarted.

The voltage displayed during charging is the charging voltage and usually will be higher than the battery’s resting voltage.

If the 6V REGULAR battery type has been selected, and the battery voltage exceeds 8.5 VDC, the charging process will be aborted (see ABORTED CHARGE above). The charger will not charge a 12V battery if “6V REGULAR has been selected.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Send Warranty Product Repairs to Table of Contents Important Safety Instructions Help US Help YOUPersonal Safety Precautions Before Using Your Battery Charger Preparing Your Battery to be ChargedUsing AN Extension Cord Plugging ITCharging Battery in the Vehicle Operating InstructionsNegative Grounded System Charging Battery Removed from the Vehicle Using Engine StartSCF-10000A Control Panel Display Mode Switch Charge Rate SwitchBattery Type Switch Charger ControlMode of Operation Control Panel GuideDigital Display Using the BUILT-IN Battery Tester Using Your Engine Starter Starting SequenceEngine Starting Notes Using Your Battery Charger Charging Tips Battery Percent and Charge Time Troubleshooting Problem Possible Cause SolutionMaintenance and Care Limited WarrantyManuel d’utilisation Faire parvenir les produits à réparer sous garantie àTable DES Matières Consignes DE Sécurité Importantes Conservez CES InstructionsAIDEZ-NOUS À Vous Aider N’oubliez pas Mesures DE Sécurité Personnelles Avant D’UTILISER LE Chargeur DE Batterie Préparer LA Batterie Pour LA ChargeBranchement Utilisation D’UNE RallongeConsignes D’UTILISATION Charge DE LA Batterie Dans LE Compartiment MoteurCircuit À Masse Négative Branchement à un circuit à masseCharge DE LA Batterie Hors DU Véhicule Circuit DE Démarrage ’URGENCETableau DE Commande DU Chargeur Commutateur DE Taux DE ChargeCommutateur DE Type DE Batterie Guide Tableau DE Commande Tableau DE Commande DU Modèle SCF-10000AUtilisation DU Testeur DE Batterie Intégré Page Utilisation DU Circuit DE Démarrage D’URGENCE Séquence DE DémarrageDémarrage D’URGENCE Utilisation DU Chargeur DE Batterie Conseils Pour LA ChargePourcentage ET Temps DE Charge Compléter un cycle de charge interrompu si leTableau DE Dépannage Anomalie Cause Probable CorrectifEntretien Garantie Limitée

SCF-10000A specifications

The Schumacher SCF-10000A is a prominent jump starter and power bank that has gained immense popularity among automotive enthusiasts and everyday drivers alike. This device is specifically designed to provide a reliable and efficient solution for jump-starting vehicles and powering various electronic devices. With a robust set of features and advanced technologies, it stands out in a crowded market.

One of the main features of the SCF-10000A is its impressive jump-starting capability. This compact unit can deliver a peak current of up to 10,000 amps, making it suitable for starting a wide range of vehicles, including cars, trucks, motorcycles, and even boats. The device is equipped with heavy-duty jumper cables that ensure a secure connection and prevent any accidental sparks, enhancing user safety during operation.

In addition to its jump-starting abilities, the Schumacher SCF-10000A functions as a multi-purpose power bank. It comes with multiple USB ports, allowing users to charge smartphones, tablets, and other devices while on the go. This feature adds a layer of convenience, making it an ideal companion for road trips, outdoor adventures, or emergency situations.

Durability and reliability are essential characteristics of the SCF-10000A. The unit is housed in a rugged, impact-resistant casing that is designed to withstand harsh conditions, ensuring longevity. Additionally, the device features an integrated LED flashlight with multiple modes, including SOS and strobe, which can be a lifesaver during emergencies or low-light situations.

Technologically, the SCF-10000A incorporates smart charging technology that automatically detects the power requirements of connected devices. This ensures optimal charging efficiency and protects against overcharging, overheating, and short circuits. The built-in LCD screen provides real-time information on battery status, output voltage, and charging progress, giving users valuable insights into the device's performance.

The Schumacher SCF-10000A is also engineered with safety features, including reverse polarity protection, ensuring that incorrect jumper cable connections do not cause damage to the vehicle or the unit itself. With these considerations in mind, this powerful jump starter and power bank provide an unmatched combination of performance, convenience, and safety, making it an essential tool for any driver.
Top Page Image Contents