Sanyo Cool/Dry Connecting Tubing between Indoor and Outdoor Units, Finishing the Installation

Page 18

05-424 KS0971-1271 12/13/05 1:28 PM Page 18

5-4. Connecting Tubing between Indoor and Outdoor Units

a)Tightly connect the indoor side refrigerant tubing exten- ded from the wall with the outdoor side tubing. (Fig. 52)

b)To fasten the flare nuts, apply specified torque as:

Table 6

Tube Dia.

Tightening Torque

 

 

1/4" (6.35 mm)

Approx. 120 – 160 lbs·in (140 – 180 kgf·cm)

 

 

3/8" (9.52 mm)

Approx. 300 – 360 lbs·in (340 – 420 kgf·cm)

 

 

1/2" (12.70 mm)

Approx. 430 – 540 lbs·in (490 – 610 kgf·cm)

 

 

5/8" (15.88 mm)

Approx. 590 – 710 lbs·in (680 – 820 kgf·cm)

 

 

5-5. Insulation of Refrigerant Tubing

IMPORTANT

To prevent heat loss and wet floors due to dripping of con-

densation, both tubes must be well insulated with a proper insulation material. (Fig. 53)

The thickness of the insulation should be a minimum 5/16" (8 mm). (Fig. 54)

Torque wrench

Spanner

Indoor unit

Outdoor unit

Fig. 52

 

Insulation

 

Fig. 53

 

Insulation

 

Thickness:

Min.

min. 5/16"

5/16"

(8 mm)

(8 mm)

 

5-6. Taping the Tubes

CAUTION

After a tube has been insulat- ed, never try to bend it into a narrow curve, as this may cause the tube to break or crack.

Fig. 54

(1)At this time, the 2 refrigerant tubes (and electrical wire if local codes permit) should be taped together with armoring tape. The drain hose may also be included and taped together as 1 bundle with the tubing.

(2)Wrap the armoring tape from the bottom of the outdoor unit to the top of the tubing where it enters the wall. As you wrap the tubing, overlap half of each previous tape turn. (Fig. 55)

(3)Clamp the tubing bundle to wall, using 1 clamp approx. every 47" (120 cm).

NOTE

Do not wind the armoring tape too tightly, since this will decrease the heat insulation effect. Also, be sure the con- densation drain hose splits away from the bundle and drips clear of the unit and the tubing.

5-7. Finishing the Installation

After finishing insulating and taping over the tubing, use sealing putty to seal off the hole in the wall to prevent rain and draft from entering. (Fig. 56)

Clamp

Insulated tubes

Fig. 55

Apply putty here

Tubing

Fig. 56

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Installation Instructions Contents…In a Room For safe installation and trouble-free operation, you must…In a Ceiling or Wall …In Moist or Uneven LocationsGeneral Tools Required for Installation not suppliedAccessories Supplied with Unit Table Optional Copper Tubing KitInstallation Site Selection Additional Materials Required for InstallationIndoor Unit Outdoor Unit Baffle Plate for the Outdoor Unit CLxx models onlyRemove the Rear Panel from the Unit How to Install the Indoor UnitTrical wiring or conduits are Make a HoleIf Block, Brick, Concrete or Similar Type Wall Install the Rear Panel on the WallIf Wooden Wall Hole DiaRemove the Grille to Install the Indoor Unit How to replace the grilleWiring Instructions General precautions on wiring Shape the Indoor Side TubingRecommended Wire Length and Diameter Wiring Instructions for Inter-unit Connections How to connect wiring to the terminal For Indoor Unit For Outdoor Unit For solid core wiring or F-cableFor stranded wiring Mounting Right-side tubingDrain hose Switching drain hose and drain capLeft-side tubing Drain capTo unmount indoor unit Do not supply power toTubing and wiring to the out Unit or operate it until allHow to Install the Outdoor Unit First refer to . Installation Site SelectionWiring Instructions for the Outdoor Unit Refrigerant Tubing Flaring Procedure with a Flare ToolTo 0.5 mm Adjust so that the amount of tube Use of the Flaring MethodInsulation of Refrigerant Tubing Connecting Tubing between Indoor and Outdoor UnitsFinishing the Installation To prevent heat loss and wet floors due to dripping of conAir Purging Be sure to completely insert Hex wrench beforeAttempting to turn the valve How to Test Run the Air Conditioner Basic Functions of the Service Valves Pump DownRemote Control Unit Installation Position To take out the remote control unit, pull it forwardMounting on a Wall Address Switch Address Setting of the Remote Control Unit

Cool/Dry specifications

The Sanyo Cool/Dry air conditioning unit is a versatile and efficient solution designed to provide optimal indoor comfort across varying climate conditions. Known for its advanced technologies and features, the Sanyo Cool/Dry offers an ideal balance between performance and energy efficiency, making it a popular choice among consumers looking for reliable cooling and dehumidifying capabilities.

One of the standout features of the Sanyo Cool/Dry is its multi-function capability. This unit is designed to operate in two modes: cool and dry, allowing users to effortlessly switch between air conditioning and dehumidification based on their needs. The cooling function ensures that rooms are kept at comfortable temperatures even during the hottest days, while the dry mode effectively reduces humidity levels, promoting a healthier indoor environment.

Energy efficiency is a hallmark of this model, as it includes advanced technologies that minimize energy consumption without sacrificing performance. The Sanyo Cool/Dry is equipped with a high-efficiency compressor that adapts its power according to the cooling demand. This inverter technology not only ensures a quieter operation but also significantly reduces electricity bills, making it an eco-friendly choice for environmentally-conscious consumers.

This air conditioning unit also comes with an intelligent control system that allows for easy operation and programming. Users can adjust their desired temperature settings with a remote control, which enhances convenience. Some models may even feature smart home integration capabilities, enabling users to monitor and control their air conditioning units through smartphone applications.

Another important characteristic of the Sanyo Cool/Dry is its air purification features. Many models include advanced filters designed to capture allergens, dust, and other airborne particles, helping to improve indoor air quality. This is particularly beneficial for those with allergies or respiratory issues, as it creates a cleaner and healthier living space.

Quiet operation is another highlight of the Sanyo Cool/Dry, making it suitable for residential environments where noise levels need to be kept to a minimum. This is ideal for bedrooms, offices, or any space where tranquility is prized.

In summary, the Sanyo Cool/Dry air conditioning unit combines efficiency, versatility, and user-friendly features, making it a standout option for those seeking effective climate control solutions. With its dual-mode functionality, energy-efficient technology, smart operation, and air purification capabilities, it satisfies a wide range of consumer needs while enhancing overall comfort in living and working spaces.
Top Page Image Contents