RIDGID R81030 manual Operation

Page 10

OPERATION

WARNING:

Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury.

WARNING:

Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes resulting in possible serious injury.

WARNING:

Do not use any attachments or accessories not recommended by the manufacturer of this tool. The use of attachments or accessories not recommended can result in serious personal injury.

APPLICATIONS

You may use this tool for the purposes listed below:

n�Driving screws with screwdriver bits

n�Light-duty drilling

CAUTION:

If at any point during the charging process none of the LEDs are lit, remove the battery pack from the charger to avoid damaging the product. DO NOT insert another battery. Return the charger and battery to your nearest service center for service or replacement.

CHARGING THE BATTERY PACK

The battery pack for this tool has been shipped in a low charge condition to prevent possible problems. Therefore, you should charge it until the light on front of charger changes from flashing green to continuous green.

NOTE: Batteries will not reach full charge the first time they are charged. Allow several cycles (operation followed by recharging) for them to become fully charged. This is normal for nickel-cadmium batteries.

TO CHARGE

See Figure 2.

nCharge the battery pack only with the charger provided. n Make sure the power supply is normal household voltage,

120 volts, 60 Hz, AC only.

nConnect the charger to a power supply.

nAttach the battery pack to the charger by aligning the raised ribs on the battery pack with the grooves in the charger, then slide the battery pack onto the charger.

nAfter normal usage, 20 minutes of charging time is required to be fully charged.

Fig. 2

nThe battery pack will become slightly warm to the touch while charging. This is normal and does not indicate a problem.

nDo not place the charger in an area of extreme heat or cold. It will work best at normal room temperature.

nWhen the batteries become fully charged, unplug the charger from the power supply and remove the battery pack.

IMPORTANT INFORMATION FOR RECHARG- ING A HOT BATTERY PACK

When using the tool continuously, the batteries in the battery pack will become hot. You should let a hot battery pack cool down for approximately 20 minutes before attempting to recharge. When the battery pack becomes discharged and is hot, the green LED will be off and the red LED will begin flashing.

When the battery pack cools down to approximately 104°F (40°C), the charger will automatically begin fast charge mode.

If the red LED continues to flash for more than 90 minutes, and the green LED remains off, this may indicate a damaged battery that will not charge.

IMPORTANT INFORMATION FOR RECHARG- ING A COOL BATTERY PACK

If the battery pack is below normal temperature range, the red LED will begin flashing and the green LED will be off. When the battery warms to a temperature of more than 41°F (5°C), the charger will automatically begin fast charge mode.

NOTE: Refer to CHARGING THE BATTERY PACK for normal recharging of batteries. If the charger does not charge your battery pack under normal circumstances, return both the battery pack and charger to your nearest repair center for electrical check. For the location of your nearest repair center, please call 1-866-539-1710.

10

Image 10
Contents OPERATOR’S Manual Table of Contents IntroductionElectrical Safety General Safety RulesWork Area Safety Personal SafetyBattery Tool USE and Care Specific Safety RulesService Safety Rules for Charger Symbols Symbol Name DESIGNATION/EXPLANATIONSymbol Signal Meaning Product Specifications FeaturesSwitch Trigger Assembly Operation Power Indicator Evaluate Indicator Charging Full LED Function of ChargerTo Remove Battery Pack To Install Battery PackLatches Adjusting To Decrease Ring Torque To Increase Adjustable Torque ClutchAdjusting Torque Reverse ForwardSTICK/PISTOL Position Installing BitsCoupler Locking Using the ScrewdriverRemoving Bits Groove BIT CouplerBattery Pack Removal Preparation for Recycling MaintenanceGeneral Maintenance BatteriesWhat is Covered Under the 3 Year Limited Service Warranty WarrantyDAY Satisfaction Guarantee Policy HOW to Obtain Service What is not CoveredCustomer Service Information