Transporting, Operating Checklist | Land Pride Powered Ditchers

Table of Contents

Section 2: Operating Instructions

Land Pride

Transporting

5.DO NOT engage PTO with machine in the fully raised position.

IMPORTANT: ALWAYS disengage PTO before raising the Powered Ditcher to transport position.

1.When raising the Powered Ditcher to the transport position, be sure that the powershaft does not contact tractor or implement.

2.Be sure to reduce tractor ground speed when turning. Leave enough clearance so the Powered Ditcher does not contact obstacles such as buildings, trees or fences.

3.Select a safe ground travel speed when transporting from one area to another. When traveling on roadways, transport in such a way that faster moving vehicles may pass you safely.

4.When traveling over rough or hilly terrain, shift tractor to a lower gear.

!CAUTION

When traveling on public roads, whether at night or during the day, use accessory lights and devices for adequate warning to operators of other vehicles. Comply with all federal, state, and local laws.

Operating Checklist

		Check	Reference

		Check chain tension. Refer to “Drive	Section 3
		Check chain tension. Refer to “Drive	Section 3
		Chain Adjustment”.	page 14
		Chain Adjustment”.	page 14

		Check oil level in chaincase. Refer to	Section 4
		Check oil level in chaincase. Refer to	Section 4
		“Lubrication”.	page 18
		“Lubrication”.	page 18

		Check that all plugs have been replaced	Section 4
		Check that all plugs have been replaced	Section 4
		properly in the chaincase.	page 18
		properly in the chaincase.	page 18

		Check that all bolts and nuts are tight.	Operator’s
		Check that all bolts and nuts are tight.	Operator’s
			Manual
			Manual

		Be certain all guards and shields are in place	Operator’s
		Be certain all guards and shields are in place	Operator’s
		and secure.	Manual
		and secure.	Manual

		Grease driveline shaft and all other grease	Section 4
		Grease driveline shaft and all other grease	Section 4
		fittings. Refer to “Lubrication”.	page 18
		fittings. Refer to “Lubrication”.	page 18

		Check air pressure in gauge wheel tire. Refer	Section 8
		Check air pressure in gauge wheel tire. Refer	Section 8
		to Tire Inflation Chart for tire pressure.	page 23
		to Tire Inflation Chart for tire pressure.	page 23

Operating Instructions

1.Operate with 540 rpm PTO tractor on the DT55 and 1000 rpm PTO on the DTM55.

2.Engage PTO at approximately 200 RPM and slowly increase to proper PTO RPM.

3.Ditching should not be done in wet conditions as soil will stick to the blades and reduce the digging ability of the Ditcher.

4.DO NOT make sharp turns or attempt to back up while Ditcher is in the ground.

6.DO NOT drop 3 point hitch. Lower the Powered Ditcher slowly to the ground.

7.Ground speed should be between 3 and 5 mph for normal conditions. Under extreme rocky conditions ground speed may have to be reduced for satisfactory performance. In general, the slower the ground speed the better job.

8.Proper operating depth and ground speed are interrelated and performance of the Powered Ditcher will improve with operator experience.

9.Periodically check for foreign objects wrapped around the blades and remove them after disengaging PTO, turning off tractor, and removing ignition key.

General Operating Instructions

Now that you have familiarized yourself with the Operator’s Manual, completed the Operator’s Checklist and properly attached your Powered Ditcher to your tractor, you are almost ready to begin using your Land Pride 55 Series Powered Ditcher.

It is now time to do a running operational safety check. If at any time during this safety check if you detect a malfunction in either the Powered Ditcher or tractor, shut tractor off immediately, remove switch key, and make necessary repairs or adjustments before continuing on.

Make sure the tractor’s park brake is engaged, the tractor’s PTO is disengaged, the Powered Ditcher is slightly off of the ground and the power shaft is not in a bind. Start the tractor and then back the tractor throttle off until the engine is at low idle. With the tractor running at an idle speed, make sure if equiped, that the optional hydraulically controlled material deflector chute is operating properly for on the go adjustment with the tractor’s hydraulic controls. This is also the time to make sure that the rear hydraulic control arms will lower the Powered Ditcher from transport to working position and back without putting the power shaft into a bind. Again, lift the Powered Ditcher slightly off of the ground and raise the engine rpm slightly. Engage the PTO drive and check to make sure everything is running smoothly. If not, safely shut the tractor down and make the necessary corrections. If everything is in proper working condition, you are ready to move to the work site.

You should inspect the area where you intend to work making sure that there are no obvious debris, large rocks, or other materials that are in your working path. You will also want to make sure that there are no people, animals, pets, valuable property and/or equipment in the immediate vicinity that could be harmed by flying rocks, dirt, or debris once you engage the Powered Ditcher.

12 DT55 & DTM55 Powered Ditchers 324-053M

3/17/08

Powered Ditchers, DT55, DTM55 specifications

Land Pride DTM55 and DT55 are powerful and versatile options for those in need of high-performance implements for their compact tractors. Designed for efficiency and durability, these models stand out in the market for their innovative features and robust construction.

One of the primary attributes of the DTM55 and DT55 series is their impressive compatibility with a wide range of compact tractors, allowing operators to maximize productivity across various applications. These models are engineered to handle tasks such as tilling, cultivating, and preparing seedbeds with ease. The adaptability to different tractors ensures that users can make the most of their equipment investment, enhancing overall efficiency on the field.

Both the DTM55 and DT55 feature a durable build, employing high-quality materials to withstand the demands of heavy-duty use. The robust frames and sturdy components provide resilience, ensuring these implements can tackle challenging terrain and tough working conditions. This durability is essential for farmers and landscapers who rely on their equipment day in and day out.

In terms of technology, the DTM55 and DT55 are equipped with advanced engineering that enhances performance. The specially designed blades ensure effective tilling, allowing for optimal soil aeration and preparation. This not only aids in crop health but also enhances overall yields, making these implements a worthwhile investment for serious agricultural operations.

Another notable characteristic is their ease of use. The intuitive design of the DTM55 and DT55 allows for straightforward attachment and detachment, reducing downtime and enabling operators to quickly switch between tasks. This user-friendly approach is particularly beneficial for small-scale farmers and landscape professionals who need to maximize their productivity within tight schedules.

Moreover, maintenance is simplified, thanks to accessible grease points and a design that minimizes wear on components. Routine upkeep can be performed without the hassle, ensuring that the implements remain in optimal working condition throughout their lifespan.

Ultimately, the Land Pride DTM55 and DT55 models combine compatibility, durability, advanced technology, and ease of use, making them ideal choices for anyone looking to enhance their compact tractor’s performance. Whether for agricultural, landscaping, or general ground preparation tasks, these implements prove themselves as reliable allies in achieving agricultural success.