SAFETY WARNINGS AND INSTRUCTIONS: CHARGING
1.This manual contains important safety and operating instructions.
2.Before using battery charger, read all instructions and cautionary markings on battery charger, battery pack, and product using battery pack.
3.
CAUTION: To reduce the risk of injury, charge only Black & Decker Batteries. Other types of batteries may burst causing personal injury and damage.
4.Do not expose charger to rain or snow.
5.Use of an attachment not recommended or sold by Black & Decker may result in a risk of fire, electric shock, or injury to persons.
6.To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting charger.
7.Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress.
8.An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire, electric shock or electrocution.
a.
b.An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety, and to prevent loss of power and overheating. The smaller the gauge number of the wire, the greater the capacity of the cable; that is, 16 gauge has more capacity than 18 gauge. When using more than one extension to make up the total length, be sure each extension contains at least the minimum wire size.
9.Use only the supplied charger when charging your tool. The use of any other charger could damage the tool or create a hazardous condition.
10.Use only one charger when charging.
11.Do not attempt to open the charger. There are no customer serviceable parts inside. Return to any authorized Black & Decker service center.
12.DO NOT incinerate the battery pack even if they are severely damaged or completely worn out. The battery can explode in a fire.
13.A small leakage of liquid from the battery pack cells may occur under extreme usage, charging or temperature conditions. This does not indicate a failure. However, if the outer seal is broken and this leakage gets on your skin:
a.Wash quickly with soap and water.
b.Neutralize with a mild acid such as lemon juice or vinegar.
c.If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10 minutes and seek immediate medical attention. MEDICAL NOTE: The liquid is a
CHARGING PROCEDURE
IMPORTANT: The batteries in your tool are not fully charged at the factory. Before attempting to charge them, thoroughly read all of the safety instructions. To charge the tool, follow the steps below:
1.Insert the jack plug (5) of the charger (4) into the charging port (6) in the bottom of the tool handle as shown in figure B.
2.Plug the charger into any standard 120 Volt 60 Hz electrical outlet.
3.Let the tool charge initially for 24 hours.
WARNING: When disconnecting the tool from the charger, be sure to unplug the charger
(6) from the outlet first, then disconnect the jack plug (5) from the tool.
IMPORTANT CHARGING NOTES
1.Charger will work best at normal room temperature.
2.The charger plug and the tool handle may become warm while charging. This is normal and does not indicate a problem.
3.A minimum charge time of 24 hours is required to recharge a completely discharged tool.
4.For most fix up jobs a shorter charge time may be adequate.
SAFETY WARNINGS AND INSTRUCTIONS: DRILLING
• Hold tool firmly to control its twisting action.
WARNING: Tool may stall (if overloaded or improperly used) causing a twist. To reduce the risk of injury always expect the stall. Grip the tool firmly to control the twisting action and prevent loss of control which could cause personal injury. If a stall does occur, release the trigger immediately and determine the reason for the stall before
OPERATING INSTRUCTIONS
REMOVING AND INSTALLING BITS
•Insert power hex bit or bit tip with bit tip holder into the cavity in the spindle (1) until it snaps into place.
•To remove the bit pull it straight out. If bit does not fit into spindle, rotate the bit and
TRIGGER SWITCH & FORWARD/REVERSE SLIDER
The tool is turned ON and OFF by pulling and releasing the trigger switch (2). A forward/reverse control button (3) determines the direction of the tool and also serves as a lock off button.
•To select forward rotation, release the trigger switch and push the forward/reverse button forward as shown in figure D.
•To select reverse, release the trigger switch and pull the forward/reverse button backward as shown in figure D.
•The neutral (no run) position of the button locks the tool in the off position. When changing the position of the button, be sure the trigger is released.
DRILLING
•Use sharp drill bits only.
•Drill bits for metal can be used for drilling holes in wood. These bits must be sharp and should be pulled out frequently when drilling to clear chips from the flutes.
•Support and secure work properly, as instructed in the safety Instructions.
•Use appropriate and required safety equipment, as instructed in the safety instructions.
•Secure and maintain work area, as instructed in the safety instructions.
•Use light pressure until the hole is started enough to keep the drill bit from slipping out of it.
•Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting but not so much as to stall the motor or deflect the bit
•Minimize stalling on breakthrough by reducing pressure and slowly drilling through last part of hole.
•Keep the motor running while pulling the bit out of a drilled hole. This will help reduce jamming.
•Make sure switch turns tool on and off.
WARNING: It is important to support work properly and to hold the tool firmly to prevent loss of control which could cause personal injury.
HINTS FOR OPTIMUM USE
•Always use the correct type of screwdriver bit. Never use a screwdriver bit tip without a bit tip holder
•If screws are difficult to tighten, try applying a small amount of washing liquid or soap as a lubricant.
•Always hold the tool and screwdriver bit in a straight line with the screw.
MAINTENANCE
Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (other than those listed in this manual) should be performed by authorized service centers or other qualified service personnel, always using identical replacement parts.
TROUBLESHOOTING
Problem | Possible Cause | Possible Solution |
• Tool will not start. | • Battery not charged. | • Check battery charging |
|
| requirements. |
• Battery will not charge. | • Charger not plugged in. | • Plug charger into a |
|
| working outlet. Refer to |
|
| “Important Charging |
|
| Notes” for more details. |
|
| • Check current at |
|
| receptacle by plugging in |
|
| a lamp or other appliance. |
|
| • Check to see if |
|
| receptacle is connected to |
|
| a light switch which turns |
|
| power off when you turn |
|
| out the lights. |
| • Surrounding air temperature | • Move charger and tool |
| too hot or too cold. | to a surrounding air |
|
| temperature of above 40 |
|
| degrees F (4,5°C) or |
|
| below 105 degrees F |
|
| (+40,5°C). |
For assistance with your product, visit our website www.blackanddecker.com for the location of the service center nearest you or call the BLACK & DECKER help line at
1-800-544-6986. Accessories
Recommended accessories for use with your tool are available from your local dealer or authorized service center. If you need assistance regarding accessories, please call:
WARNING: The use of any accessory not recommended for use with this tool could be hazardous.
BATTERY REMOVAL
Before attempting to disassemble this tool, turn it on and run it in either direction until it stops to ensure a complete discharge of the batteries. Using a phillips screwdriver, remove the screws in the product housing and lift the housing half from the tool. Disconnect the terminal clips from the batteries and lift the batteries out. See “Service Information” for battery replacement.
THE RBRC™ SEAL
The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the nickel- 
metal hydride battery (or battery pack) indicates that the costs to recycle the 
battery (or battery pack) at the end of its useful life have already been paid by Black & Decker. In some areas, it is illegal to place spent
RBRC in cooperation with Black & Decker and other battery users, has established programs in the United States and Canada to facilitate the collection of spent
SERVICE INFORMATION
All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you. To find your local service location, refer to the yellow page directory under
FULL TWO-YEAR HOME USE WARRANTY
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The defective product will be replaced or repaired at no charge in either of two ways.
The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a participating retailer). Returns should be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for repair or replacement at our option. Proof of purchase may be required. Black & Decker owned and authorized Service Centers are listed under "Tools- Electric" in the yellow pages of the phone directory and on our website www.blackanddecker.com.
This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other rights which vary from state to state. Should you have any questions, contact the manager of your nearest Black & Decker Service Center. This product is not intended for commercial use.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call
Imported by | See | |
Black & Decker (U.S.) Inc., | – Yellow Pages – | |
701 | E. Joppa Rd. | for Service & Sales |
Towson, | MD 21286 U.S.A. |
|
|
|
|
|
|
|
Numéros de catalogue CSD300T
MERCI D’AVOIR CHOISI BLACK & DECKER !
VISITEZ WWW.BLACKANDDECKER.COM/NEWOWNER
POUR ENREGISTRER VOTRE NOUVEAU PRODUIT.
AVANT DE RETOURNER CE PRODUIT POUR QUELQUE
RAISON QUE CE SOIT, COMPOSER LE
AVANT D’APPELER, AYEZ EN MAIN LE N° DE CATALOGUE ET LE CODE DE DATE. DANS LAPLUPART
DES CAS, UN REPRÉSENTANT DE BLACK & DECKER PEUT RÉSOUDRE LE PROBLÈME PAR TÉLÉPHONE. SI VOUS AVEZ UNE SUGGESTION OU UN COMMENTAIRE,