Porter-Cable 844 Charging the Battery Pack, Normal Charging, Installing or Removing Battery Pack

Page 11

CHARGING THE BATTERY PACK

Before using your cordless tool for the first time, fully charge the battery pack. If the battery pack is installed, remove it by following instructions under INSTALLING OR REMOVING BATTERY PACK.

NORMAL CHARGING

Make sure that the power circuit voltage is the same as that shown on the charger specification plate. Connect the charger to the power source. The red and green lights will flash once to indicate that the power is connected properly and the charger is ready for operation.

Position the battery pack on charger, align the rails on the battery pack (A) Fig. 2 with the four tabs (C) Fig. 1 on the charger. Slide the battery forward

on charger until it stops.

 

 

 

 

 

 

A B

C

The green light (A) Fig. 1 should begin

 

 

 

 

 

 

 

to flash rapidly indicating that the

 

 

 

 

battery pack is receiving a “fast

 

 

 

 

charge”. [If the green light does not

 

 

 

 

flash or if the red light (B) illuminates,

 

 

 

 

see

DIAGNOSTICS].

After

 

 

 

 

approximately one hour, the “Fast

 

 

 

 

Charge” indicator light should glow

 

 

 

 

continually, indicating that the battery

 

 

 

 

 

 

 

Fig. 1

pack is fully charged and that the

 

charger is now in a “Maintenance Charge” mode. The battery pack can be left on “Maintenance Charge” until you are ready to use it.

Depending on room temperature, line voltage, and existing charge level, initial battery charging may take longer than one hour.

Disconnect the charger from the power source when not in use.

INSTALLING OR REMOVING BATTERY PACK

Always set the trigger switch to the locked OFF position when installing or removing the battery pack.

TO REMOVE BATTERY PACK: Depress the battery release

B

 

button (B) Fig. 2, and pull battery pack

 

 

out of tool.

A

 

TO INSTALL BATTERY PACK: Align

 

 

 

 

rails (A) Fig. 2, on battery pack with

 

 

slots on tool and push battery pack

 

 

onto tool until it locks in place.

 

 

 

 

 

Fig. 2

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Cordless Circular Saw Important Safety Instructions Table of ContentsCalifornia Proposition Safety Guidelines DefinitionsGeneral Safety Rules General Safety Rules Safety Instructions for All Saws Additional Specific Safety RulesAdditional Specific Safety Rules Lower Guard Safety Instructions Safety Instructions for Charger and Batteries Do not charge battery in damp or wet locations Normal Charging Charging the Battery PackInstalling or Removing Battery Pack Diagnostics Battery OperationCarton Contents Starting and Stopping the SAW Assembly OperationFunctional Description ForewordTelescoping Guard Installing the BladeTo Adjust for Bevel Cuts To Adjust Depth of CUT45 Bevel Positive Stops To Adjust 90 Positive StopTo Adjust 45 Positive Stop Line of CUT IndicatorTo Attach the Base Insert Installing Sawdust Exhaust NozzleTo Attach RIP Guide Installation and Care of Dust BAGVacuum Cleaner Adapter Ripping HOW to USE the SAWCrosscutting Pocket Cuts Plunge Cutting Bevel CuttingLubrication Troubleshooting MaintenanceKeep Tool Clean Failure to StartReplacement Parts Service and Repairs ServiceAccessories WarrantyCanadian PORTER-CABLE Delta Service Centers

844 specifications

The Porter-Cable 844 is a highly regarded portable benchtop planer, designed to combine power, precision, and convenience for both professional woodworkers and DIY enthusiasts. This planer features a robust 15-amp motor that delivers a substantial 20,000 RPM, ensuring efficient stock removal and smooth finishes on a variety of wood materials.

One of the standout features of the Porter-Cable 844 is its dual blade system, which utilizes two high-quality, reversible blades. This not only increases the tool's durability but also offers an extended lifespan before the need for replacement. The blades can effectively remove up to 1/8 inch of material in a single pass, making it suitable for a wide range of planing tasks, from flattening rough lumber to finishing edges for joint preparation.

The design of the 844 emphasizes user comfort and ease of operation. With a lightweight frame, it is portable enough for easy transport between job sites. Its ergonomic handles provide a comfortable grip, reducing fatigue during extended use. The integrated dust port is another practical feature, allowing for efficient dust collection when attached to a vacuum system. This functionality keeps the workspace tidy and enhances visibility while working.

Porter-Cable’s innovative feed system is designed for consistent and dependable operation. Featuring a variable speed option, the feed rate can be adjusted according to the specifics of the project, which allows users to tailor the planing process to different wood types and thicknesses. The adjustable table height is another beneficial characteristic, allowing for precise depth settings to accommodate various machining requirements.

Safety features are paramount in the design of the Porter-Cable 844. It includes a safety lock-off switch that prevents accidental starts, ensuring a secure operating environment. The combination of power, precision, and user-friendly features makes the Porter-Cable 844 a versatile and essential tool for anyone serious about woodworking.

In summary, the Porter-Cable 844 stands out in its class due to its powerful motor, dual blade capabilities, adjustability, and safety features. Whether you are looking to smooth out rough cuts, prepare wood for joining, or achieve a fine finish on your projects, the Porter-Cable 844 provides the performance and reliability you need to get the job done efficiently. It is a top choice for professional craftsmen and hobbyists alike, ensuring excellent results on each planing task.
Top Page Image Contents