Black & Decker PHS550B Functional Description, Operating Instructions, Troubleshooting

Page 2

Functional

A

 

 

 

Description

 

 

 

 

 

 

 

1.

Variable Speed Switch

 

 

 

2

2.

Lock-off button

 

5

 

 

3.

Blade release

 

 

1

4

4.

Soft grip

 

 

 

 

 

 

 

5.

Second hand position

 

 

 

 

6.

Large capacity blade

 

3

 

 

7.

Metal cutting blade

 

 

 

 

8.

Tooth Protector

 

 

 

 

 

 

6

7

 

8

B

 

C

 

 

D E

F

Motor

Your tool is powered by a Black & Decker specified motor. Be sure your power supply agrees with the nameplate marking. A marking of 120 volts, 50/60 Hz or 120 volts, AC only means that the tool is designed to operate on normal 120 volt house current. Voltage decrease of more that 10% will cause loss of power and overheating. All Black & Decker tools are factory tested. If this tool does not run, check the power supply.

Removing & Refitting the Blade

WARNING: Always ensure the unit is unplugged from the power supply when changing blades.

Your saw has a new blade clamping mechanism. Before using the saw familiarize yourself with the removal of the blade and refitting the blade securely in the saw. Always ensure the tooth protector is fitted when changing blades.

Removing the Blade (Figure B)

Ensure blade has cooled after use. Press and hold the rear of the blade release button fully, hold the back of the blade and rotate it through 90 degrees until the toothed side of the blade meets the housing. Slide the blade sideways off the retaining pin and remove from the saw.

Fitting a Blade (Figures C,D)

Place the blade, with the tooth protector fitted, over the location pin. The blade teeth should be facing the handle. (Fig. C)

Note: To ensure that the blade fits properly, make sure the locking pin position mirrors that of the blade shank cut-out. The flat side of the locking pin should be parallel to the bottom of the saw as shown in the insert of Fig. C. (Housing cover removed for clarity.) If the locking pin is not parallel to the bottom of the saw, use a flat bladed screwdriver to rotate the pin back to the proper starting position.

Rotate the blade through 90° until it is fully located in the slot and the location pin is in the locked position. (Fig. D)

To ensure the blade is securely fitted try to remove without pressing the blade release button. Remove the tooth protector, your saw is now ready for use.

Operating Instructions

Variable Speed Trigger Switch (Figure E)

Your saw is equipped with a variable speed trigger switch that allows you greater control over start of cut, rate of cut and breakthrough of cut.

To switch your saw on, push lock-off button (2) and squeeze the on/off variable speed trigger switch (1). To switch off, release the trigger, the unit will automatically lock-off.

Using Tool (Figure F)

Hold tool with two hands as shown in Figure F. To obtain the best results from your saw, use the same backward and forward movement you would employ with a traditional hand saw. This will enable a quicker cleaner cut.

Cutting Metal

Your saw can be used for cutting light gauge ferrous and non-ferrous metals such as copper, brass, aluminum, etc. with the specified blade. See recommended materials.

It is advisable when cutting thin sheet to clamp a backing sheet of soft wood or plywood to the work as this will enable you to obtain a cleaner cut. Both metal and wood backing are sawn together. Do not force the cutting blade into the metal as this will reduce the life of the blade and possibly damage the motor. Cutting thin metal will take longer than cutting even a relatively thick piece of wood, so do not be tempted to speed up the operation by forcing the saw. Only use the metal cutting blade for this purpose.

Recommended Materials

 

Recommended Materials

Capacity

Large Capacity Blade

Up to 4 in. (102mm) x 4 in. (102mm)

Soft wood

Plastic soil pipe

Up to 4-7/8 in. (124mm)

Metal Cutting Blade

Up to 1/8 in. (3mm) thick

Ferrous/non-ferrous metals

Troubleshooting

Problem

Possible Cause

Possible Solution

• Unit will not start.

• Cord not plugged in.

• Plug tool into a working

 

• Circuit fuse is blown.

outlet.

 

• Replace circuit fuse.

 

 

(If the product repeatedly

 

 

causes the circuit fuse to

 

 

blow, discontinue use

 

 

immediately and have it

 

 

serviced at a Black & 

 

 

Decker service center or

 

• Circuit breaker is tripped.

authorized servicer.)

 

• Reset circuit breaker.

 

 

(If the product repeatedly

 

 

causes the circuit

 

 

breaker to trip,

 

 

discontinue use

 

 

immediately and have it

 

 

serviced at a Black & 

 

 

Decker service center or

 

• Cord or switch is damaged.

authorized servicer.)

 

• Have cord or switch

 

 

replaced at Black 

 

 

& Decker Service Center

 

 

or Authorized Servicer.

For assistance with your product, visit our website www.blackanddecker.com for the location of the service center nearest you or call the BLACK & DECKER help line at

1-800-544-6986.

Maintenance / Cleaning

Use only mild soap and damp cloth to clean the tool. Many household cleaners contain chemicals which could seriously damage the plastic and gel components. Also do not use gasoline, turpentine, lacquer or paint thinners or similar products. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.

IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by authorized service centers or other qualified service personnel, always using identical replacement parts.

Accessories

Recommended accessories for use with your tool are available from your local dealer or authorized service center. If you need assistance regarding accessories, please call:

1-800-54-HOW-TO. (800-544-6986)

WARNING: The use of any accessory not recommended for use with this tool could be hazardous.

Service Information

All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you. To find your local service location, refer to the yellow page directory under “Tools—Electric” or call: 1-800-544-6986 or visit www.blackanddecker.com

Full Two-Year Home Use Warranty

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The defective product will be replaced or repaired at no charge in either of two ways.

The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a participating retailer). Returns should be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges.

The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for repair or replacement at our option. Proof of purchase may be required. Black & Decker owned and authorized Service Centers are listed under “Tools-Electric” in the yellow pages of the phone directory and available on our website www.blackanddecker.com.

This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other rights which vary from state to state. Should you have any ques- tions, contact the manager of your nearest Black & Decker Service Center. This product is not intended for commercial use.

Free warning label replacement: If your warning labels become illegible or are missing, call 1-800-544-6986 for a free replacement.

Black & Decker (U.S.)

See ‘Tools-

Inc.,

Electric’

701 E. Joppa Rd.

– Yellow Pages –

Towson, MD 21286

for Service &

U.S.A.

Sales

 

Image 2
Contents Safety Guidelines Definitions General Safety RulesSpecific Safety Rules Save this manual for Future referenceOperating Instructions TroubleshootingFunctional Description Conserver ce manuel pour un usage ultérieur Règles de sécurité spécifiquesDe catalogue PHS550G, PHS550B Lignes directrices en matière de sécurité définitionsConserve este manual para futuras consultas Description fonctionnelleCatálogo N PHS550G, PHS550B Pautas DE SEGURIDAD/DEFINICIONESNormas de seguridad específicas Instrucciones de operaciónDetección de problemas Materiales recomendados Capacidad
Related manuals
Manual 6 pages 27.61 Kb

PHS550B specifications

The Black & Decker PHS550B is a powerful and versatile electric saw designed for both DIY enthusiasts and professionals alike. With its lightweight design and compact structure, this saw provides exceptional maneuverability, making it ideal for a variety of cutting tasks. Whether you're trimming branches, cutting through fencing, or tackling general renovation projects, the PHS550B is engineered to deliver precise results.

One of the standout features of the PHS550B is its 3.4-amp motor, which offers robust cutting power that can easily handle most cutting jobs. The variable speed control allows users to adjust the speed of the blade, providing flexibility for different materials and applications. Whether you need to make slow, careful cuts or fast, aggressive ones, this saw can accommodate your needs.

The saw is equipped with a 4-inch blade that enables smooth and efficient cutting through wood, plastic, and more. The tool-less blade change feature adds to its convenience, allowing users to switch blades quickly and easily without the need for additional tools. This means you can spend more time cutting and less time fussing with setup.

Safety is a priority with the Black & Decker PHS550B. The saw includes a built-in safety lock-off switch to prevent accidental starts, ensuring that users can operate the tool with peace of mind. The integrated cord retention system helps keep the power cord secure, reducing the risk of dangerous snags while working.

Its ergonomic design contributes to user comfort during extended use. The soft-grip handle minimizes vibrations, while the lightweight body ensures that prolonged operation does not lead to fatigue. This thoughtful engineering allows both seasoned professionals and casual users to maintain control and precision while working on their projects.

In summary, the Black & Decker PHS550B is a compact and efficient electric saw that features a powerful motor, variable speed control, and a tool-less blade change system. Its focus on safety and user comfort makes it an excellent choice for anyone looking to tackle cutting tasks with confidence and precision. Whether for home improvement, landscaping, or light construction, the PHS550B is sure to meet and exceed expectations.