Black & Decker BDCDMT1206KITS 12volt max* Charging Procedure, Bad battery, Hot/Cold pack delay

Page 7

•DO NOT splash or immerse in water or other liquids. This may cause premature cell failure.

•Do not store or use the tool and battery pack in locations where the temperature may reach or exceed 105°F (40˚C) (such as outside sheds or metal buildings in summer).

WARNING: Never attempt to open the battery pack for any reason. If battery pack case is cracked or damaged, do not insert into charger. Do not crush, drop or damage battery pack. Do not use a battery pack or charger that has received a sharp blow, been dropped, run over or damaged in any way (i.e., pierced with a nail, hit with a hammer, stepped on). Damaged battery packs should be returned to service center for recycling.

WARNING: Fire hazard. Do not store or carry battery so that metal objects can contact exposed battery terminals. For example, do not place battery in aprons, pockets, tool boxes, product kit boxes, drawers, etc., with loose nails, screws, keys, etc. Transporting batteries can possibly cause fires if the battery terminals inadvertently come in contact with conductive materials such as keys, coins, hand tools and the like. The US Department of Transportation Hazardous Material Regulations (HMR) actually prohibit transporting batteries in commerce or on airplanes (i.e., packed in suitcases and carry-on luggage) UNLESS they are properly protected from short circuits. So when transporting individual batteries, make sure that the battery terminals are protected and well insulated from materials that could contact them and cause a short circuit.

NOTE: Lithium-Ion batteries should not be put in checked baggage.

Storage Recommendations

1. The best storage place is one that is cool and dry away from direct sunlight and excess heat or cold. 2. Long storage will not harm the battery pack or charger.

12volt max* Battery Pack (BDCDMT112) Charging, Installing, and Removing

12volt max* Charging Procedure

A

Black & Decker chargers are designed to charge Black & Decker

 

battery packs in 30-60 minutes depending on the pack being charged.

 

1. Plug the charger (1) into an appropriate outlet before inserting the

 

battery pack (2).

 

2. Insert the battery pack into the charger. (Figure A)

 

 

 

 

3. The green LED will flash indicating that the battery pack is

 

 

 

 

 

 

 

being charged.

 

 

 

 

 

 

 

4. The completion of charge is indicated by the green LED

 

 

 

 

 

 

 

 

remaining on continuously. The battery pack is fully charged

 

 

 

 

 

 

 

 

and may be used at this time or left on the charger.

 

Recharge discharged batteries as soon as possible after use or battery life may be greatly diminished. For longest battery life, do not discharge batteries fully. It is recommended that the batteries be recharged after each use.

Charger Diagnostics

This charger is designed to detect certain problems that can arise with the battery packs or the power source. Problems are indicated by one LED flashing in different patterns.

Bad battery

The charger can detect a weak or damaged battery. The red LED flashes in the pattern indicated on the label. If you see this bad battery blink pattern, do not continue to charge

the battery. Return it to a service center or a collection site for recycling.

Hot/Cold pack delay

When the charger detects a battery that is excessively hot or excessively cold, it automatically

starts a Hot/Cold Pack Delay, suspending charging until the battery has normalized. After this happens, the charger automatically switches to the Pack Charging mode. This feature ensures maximum battery life. The red LED flashes in the pattern indicated on the label.

important charging notes

1. Longest life and best performance can be obtained if the battery pack is charged when the air temperature is between 65°F and 75°F (18°- 24°C). DO NOT charge the battery pack in an air temperature below +40°F (+4.5°C), or above +105°F (+40.5°C). This is important and will prevent serious damage to the battery pack.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Save this manual for Future reference Catalog Number BDCDMT112 12V MAX BDCDMT120 20V MAXVEA EL ESPA-OL EN LA Contraportada Work Area Safety Safety Guidelines DefinitionsSpecific Safety Rules Symbols Always Wear Certified Safety EQUIPMENT FUNCTIONAL DESCRIPTION Important Safety Instructions for Battery ChargersVolts Read all InstructionsImportant charging notes 12volt max* Charging ProcedureBad battery Hot/Cold pack delay20volt Max** Charging Procedure Leaving the battery in the charger Operating Drill/Screwdriver attachment Operating Power UnitOn-board bit storage Screw drivingKeyless Chuck figure H Torque Control figureRbrc Seal TroubleshootingService Information Full Two-Year Home Use Warranty BatteryDe catalogue BDCDMT112 12V MAX BDCDMT120 20V MAX Mode D’EMPLOILignes directrices en matière de sécurité définitions Page Règles de sécurité spécifiques Description Fonctionnelle SymbolesAvertissement Tension Longueur totale du cordon en pieds Lire toutes les directives12volt max* Procédure de charge Fonction de suspension du bloc-piles chaud/froid Pile en mauvais étatRemarques importantes pour le chargement Bloc-piles laissé dans le chargeur 20volt Max** Procédure de chargeDétente ET Commutateur Coulissant AVANT/ARRIÈRE 20volt Max** Insertion et retrait du bloc-piles de l’outilAvertissement de sécurité et directives perceuses Installation ET Retrait DES Modules Figure GPerçage VissageRéglage du couple figure Rangement intégré des mèchesEntretien DépannagePerçage DU Bois Perçage DU MétalAccessoires Page Catálogo N BDCDMT112 12V MAX BDCDMT120 20V MAX Manual DE InstruccionesPautas DE SEGURIDAD/DEFINICIONES Page Normas de seguridad específicas Símbolos Descripción de las funcionesAdvertencia Amperaje Lea todas las instruccionesMÁX* BDCDMT112 Recomendaciones con respecto al almacenamiento12volt max* Procedimiento de carga Notas importantes sobre la carga Diagnóstico del cargadorBatería en mal estado Retraso por paquete caliente/fríoDejar la batería en el cargador Para extraer el paquete de baterías Presione el botónMÁX** BDCDMT120 20volt Max** Procedimiento de cargaPara instalar el paquete de baterías Inserte el Precaución Riesgo de descarga eléctrica. Bajo Instalación Y Extracción DE Aditamentos Figura GAdvertencia Peligro de quemaduras. Las piezas Ajuste del control de torsión figura Colocación Y Extracción DE UNA Broca O UNA PuntaDestornillado Portabrocas sin llave figura HTaladrado Detección de problemasProblema Causa posible Solución posible Espacio en la herramienta para guardar brocasAccesorios MantenimientoReemplazo DE LAS Etiquetas DE Advertencia Esta Garantia no Aplica Cuando OS DE GarantiaSolamente Para Propositos DE Mexico Para Servicio y ventas Eléctricas Tools-Electric Páginas amarillas

BDCDMT1206KITS specifications

The Black & Decker BDCDMT1206KITS is a versatile and powerful tool kit that caters to both DIY enthusiasts and professionals alike. Designed for efficiency and ease of use, this kit includes a range of features and technologies that make it a standout choice in the market.

One of the main features of the BDCDMT1206KITS is its innovative Matrix Quick Connect System. This system allows users to easily swap out attachments for various tasks, making the tool incredibly adaptable. The kit comes with multiple attachments, including a drill, sander, and jigsaw, enabling users to tackle a wide range of projects without the need for multiple standalone tools.

The BDCDMT1206KITS is powered by a robust 20V MAX lithium-ion battery, which provides ample power and longevity. This battery technology ensures that you won’t be interrupted mid-project due to power failure. Additionally, the lithium-ion battery has a long shelf life and retains its charge for extended periods, making it convenient for the user. The included charger is designed to quickly recharge the battery, reducing downtime and keeping projects on track.

Comfort and usability are also key characteristics of the Black & Decker BDCDMT1206KITS. The tool features an ergonomic design that minimizes user fatigue during extended use. The lightweight construction makes the tools easy to handle, ensuring precision and control for all types of applications. The easy-to-use controls and intuitive design allow even novice users to quickly get accustomed to the tools.

The kit also includes safety features designed to protect the user during operation. Safety guards and ergonomic grips ensure that users can work confidently while minimizing the risk of accidents.

In addition to its technical specifications, the BDCDMT1206KITS is backed by Black & Decker’s reputation for quality and durability. This tool kit is well-constructed and designed to withstand the rigors of ongoing use.

Overall, the Black & Decker BDCDMT1206KITS is a comprehensive and user-friendly tool kit that combines power, versatility, and safety. It is an excellent investment for anyone looking to expand their toolkit and take on a variety of projects around the home or in a professional setting. With its innovative features and reliable performance, the BDCDMT1206KITS is sure to meet the needs of any user.
Top Page Image Contents