Makita SP6000 instruction manual Specific Safety Rules

Page 4

power tool will do the job better and safer at the rate for which it was designed.

18.Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

19.Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

20.Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

21.Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

22.Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

23.Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended

could result in a hazardous situation.

Service

24.Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

25.Follow instruction for lubricating and changing accessories.

26.Keep handles dry, clean and free from oil and grease.

GEB031-1

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to circular saw safety rules. If you use this tool unsafely or incorrectly, you can suffer serious personal injury.

Danger:

1.Keep hands away from cutting area and the blade. Keep your second hand on auxiliary handle, or motor housing. If both hands are holding the saw, they cannot be cut by the blade.

2.Do not reach underneath the workpiece or tool base. The guard cannot protect you from the blade below the workpiece. Do not attempt to remove cut material when blade is moving.

CAUTION: Blades coast after turn off. Wait until blade stops before grasping cut material.

3.Adjust the cutting depth to the thickness of the workpiece. Less than a full tooth of the blade teeth should be visible below the workpiece.

4.Never hold piece being cut in your hands or across your leg. Secure the workpiece to stable platform. It is important to support the work properly to minimize body exposure, blade binding, or loss of control.

A typical illustration of proper hand support, workpiece support, and supply cord routing (if applicable).

000157

5.Hold power tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will also make exposed metal parts of the power tool "live" and shock the operator.

6.When ripping always use a rip fence or straight edge guide. This improves the accuracy cut and reduces the chance of blade binding.

7.Always use blades with correct size and shape (diamond versus round) of arbour holes. Blades that do not match the mounting hardware of the saw will run eccentrically, causing loss of control.

8.Never use damaged or incorrect blade washers or bolt. The blade washers and bolt were specially designed for your saw, for optimum performance and safety of operation.

9.Causes and Operator Prevention of Kickback:

kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing an uncontrolled saw to lift up and out of the workpiece toward the operator;

when the blade is pinched or bound tightly by the kerf closing down, the blade stalls and the motor reaction drives the unit rapidly back

4

Image 4
Contents Plunge Cut Circular Saw Symbols SpecificationsEC Declaration of Conformity General Power Tool Safety Warnings Specific Safety Rules To avoid kickback, do support board or panel near the cut Do not support board or panel away from the cut000194 Functional Description Adjusting depth of cutBevel cutting Switch action Speed adjusting dialTilting to the right Tilting to the leftRemoving or installing saw blade AssemblyHex wrench storage Operation When using with guide rail accessorySection cutting ordinary sawing Maintenance Rip fence guide rule AccessoryGuide device accessories Adjusting for accuracy of 90 and 45 cut vertical and 45 cutAccessories Replacing carbon brushesPage Page Page Makita Corporation Anjo, Aichi, Japan