SoundCraft CPS2000 technical manual Important Safety Instructions

Page 6

IMPORTANT SAFETY INSTRUCTIONS

￿Read these instructions.

￿Keep these instructions.

￿Heed all warnings.

￿Follow all instructions.

￿Do not use this apparatus near water.

￿Clean only with a dry cloth.

￿Do not block any ventilation openings. Ventilation should not be impeded by covering the ventilation openings with items such as newspapers, table cloths, curtains etc. Install in accordance with the manufacturer’s instructions.

￿Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

￿Do not defeat the safety purpose of a polarised or grounding type plug. A polarised plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet

￿Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles and the point where they exit from the apparatus.

￿Only use attachments/accessories specified by the manufacturer.

￿Use only with the cart, stand, tripod, bracket or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

￿Unplug this apparatus during lightning storms or when unused for long periods of time.

￿Refer all servicing to qualified service personnel. It is recommended that all maintenance and service on the product should be carried out by Soundcraft or its authorised agents. Soundcraft cannot accept any liability whatsoever for any loss or damage caused by service, maintenance or repair by unauthorised personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

￿No naked flame sources, such as lighted candles, should be placed on the apparatus.

￿WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. Do not expose the apparatus to dripping or splashing and do not place objects filled with liquids, such as vases, on the apparatus.

￿Terminals marked with the lightning symbol are hazardous live and the external wiring connected to these terminals requires installation by an "instructed person" or the use of ready made leads or cords.

￿THIS APPARATUS MUST BE EARTHED. Under no circumstances should the safety earth be disconnected from the mains lead.

￿The mains supply disconnect device is the mains plug. It must remain accessible so as to be readily operable when the apparatus is in use.

￿If any part of the mains cord set is damaged, the complete cord set should be replaced. The following information is for reference only.

￿The wires in the mains lead are coloured in accordance with the following code:

￿Earth (Ground):Green and Yellow (US - Green/Yellow)

￿Neutral:Blue (US - White)

￿Live (Hot):Brown (US - Black)

￿As the colours of the wires in the mains lead may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

￿The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol

￿The wire which is coloured Blue must be connected to the terminal in the plug which is marked with the letter N

￿The wire which is coloured Brown must be connected to the terminal in the plug which is marked with the letter L

￿Ensure that these colour codes are followed carefully in the event of the plug being changed

￿This unit is capable of operating over a range of mains voltages as marked on the rear panel. It is important to ensure that the correct mains fuse is fitted before switching on the unit.

2

Introduction

Image 6
Contents Soundcraft CPS2000 EN6 3JN Contents Page Introduction Important Safety Instructions Introduction Mains Voltage SelectionMains Voltage Selector Positions Operating Voltage Range Warranty Recommendations for Installation of the CPS Recommendations for Installation General PSU Linking To ConsoleDimensions Installation Technical Specification Technical Specification Rated Input Power MaxOperating Temperature Range Ambient Circuit Description Circuit Description +/- 17V RAILS. SC3804+17V Supply. LH PCB Mains Voltage Meter Mutual Shutdown SystemOvercurrent Protection Temperature Protection System Undervoltage warning-17V Supply. RH PCB +48V Supply +8V SupplyMains Voltage Select PCB. SC3817 Fan Control PCB. SC4032 Faultfinding Notes +/- 17V RailsFuse Replacement This is DangerousCircuit Description Parts List Spare Parts Main Assemblies CPS2000 RH Module Assy Pcbs CAP Elec Vert 47UF 25V TPD SKP DZ7 RES 4W 470R VTM REG1 Miscellaneous Hardware Fan Control CPS2000 Fan Control & PCB SC4032 Technical DescriptionCPS2000 Fan Controller Circuit Diagram Fan Control Technical Drawings Technical Drawings Technical Drawings Technical Drawings Technical Drawings Technical Drawings Technical Drawings Technical Drawings Technical Drawings Technical Drawings