HP Dynamic Root Disk (DRD) manual Fsysteminformationfile

Page 68

drd unrehost[-?] [-p] -f system_information_file [-q] -t device_special_file [-v] [-x extended option=value] [-x -?] [-X option_file]

Options

-?

Displays the usage message for a DRD command. This option cannot be used with other options.

-p

Sets preview mode. When run with the -poption, a DRD command performs analysis without running the command and reports any errors.

-fsystem_information_file

Specifies the file containing the system information (hostname, IP address, network information, etc.) to be copied to EFI/HPUX/SYSINFO.TXT on the disk specified by the -toption. See sysinfo(4) for the syntax of this file. If not specified, the file defaults to /etc/opt/drd/ default_sysinfo_file.

-q

Decreases the verbosity level by one each time it is specified. For example, -qqwill reduce the verbosity from the default value of 4 to 2. If both -x verbosity=5 and -qqqare included on the command line, the effective verbosity is 2. The minimum verbosity level is 0. (See also the -x verbosity option.)

-tdevice_special_file

Specifies the block device special file of a single writeable physical disk. The file specified by the -foption will be written to EFI/HPUX/SYSINFO.TXT in the EFI partition of this disk. If no target is specified, the inactive system image is used as a target.

-v

Increases the verbosity level by one each time it is specified. For example, -vwill increase the effective verbosity from the default value of 4 to 5. If both -x verbosity=1 and -vvare included on the command line, the effective verbosity is 3. The maximum verbosity level is 5. (See also the -x verbosity option.)

-xextended_option=value

Sets the extended option to a value.

-x -?

Displays the list of possible -x(extended) options.

-Xoption_file

Gets the extended options from a file.

Extended options

The following extended options are available:

-x alternate_bootdisk=block_device_special_file

This is the alternate boot disk. The alternate boot disk must be specified as a block device special file.

-x HA_alternate_bootdisk=block_device_special_file

This is the High Availability alternate boot disk. The High Availability alternate boot disk must be specified as a block device special file. High Availability alternate boot disk is supported only on Itanium-based architecture and for PA-RISC systems that support hardware partitions.

-x ignore_unmounted_fs={truefalse}

(Default is false) Controls whether a clone fails when an unmounted file system in the root volume group is detected.

68 DRD commands

Image 68
Contents Dynamic Root Disk A.3.10.* Administrators Guide Document Part Number DRD Version Supported Operating Systems Table of Contents Troubleshooting DRD Support and other resources DRD commandsRehosting and unrehosting systems Glossary IndexList of Figures List of Examples Commands overview About Dynamic Root DiskConceptual overview TerminologyDownloading and installing Dynamic Root Disk Cloning the active system image Active system imageLocating disks Locating disks on HP-UX 11i v2 systemsLocating disks on HP-UX 11i v3 Integrity systems # /usr/sbin/ioscan -fnkC disk# /usr/sbin/ioscan -m dsf Choosing a target disk Using other utilities to determine disk availabilityUsing DRD for limited disk availability checks Using drd clone to analyze disk size Creating the cloneCloning the active system image Example 2-7 The drd clone command output Success ErrorExample 2-8 The drd clone command output for SAN disk Adding or removing a diskUpdating and maintaining software on the clone DRD-Safe commands and PackagesSwinstall Swremove Swlist Swmodify Swverify Swjob DRD-Safe patches and the drdunsafepatchlist file Kctune Update-ux View Kcmodule Kconfig Mkkernel Swm jobUpdating and managing patches with drd runcmd Special considerations for firmware patches Patches with special installation instructionsUpdating and managing products with drd runcmd Viewing logs Accessing the inactive system image Mounting the inactive system imagePerforming administrative tasks on the inactive system image Enter the patches into a file such as Compare vxconfigbackup with the clone copy Unmounting the inactive system imageUnmounting the inactive system image Page Overview Quick start-basic synchronizationTrimming the list of files to be synchronized Drd sync commandDetermining the list of files in the booted volume group Files that have changed on the clone Copying the files to the inactive clone image Drd sync system shutdown script Page Activating the inactive system image Preparing the inactive system image to activate later# /opt/drd/bin/drd activate # /usr/bin/more /stand/bootconf l /dev/dsk/c2t0d0s2 Undoing activation of the inactive system imageActivating the inactive system image Undoing activation of the inactive system image Page Rehosting examples Rehosting and unrehosting systemsRehosting overview Rehosting a mirrored image Example 7-1 Provisioning a new systemUnrehosting overview # rm /var/opt/drd/registry/registry.xmlPage Troubleshooting DRD Page Support and other resources Contacting HPRelated information Typographic conventions New and changed information in this editionLocating this guide Find1 Page Drd activate command DRD commandsDRD command syntax HAalternatebootdisk=blockdevicespecialfile Ignoreunmountedfs=truefalseLogfile=/var/opt/drd/drd.log Logverbosity=4Drd clone command Reboot=truefalseVerbosity=3 Default Copyautofile optionTtargetdevicefile Copyautofile=truefalseblockdevicespecialfileEnforcedsa=truefalse Drd deactivate command Drd mount command Example A-1 File system mount points Drd rehost command Devicespecialfile -v-xextended option=value -x-?-Xoptionfile Extended options Drd runcmd command Extended options Drd status command Alternatebootdisk=blockdevicespecialfile Drd sync command Usr/sbin/swlist -l file, orDrd umount command Excludelist=Alternatebootdisk=blockdevicespecialfile Drd unrehost command Fsysteminformationfile Mirrordisk=blockdevicespecialfile Page Booted system GlossarySystem image Index Idisk partition, 10, 11 inactive system file system