HP System Replication Adapter Software QL227 for VMware manual Verify connectivity s230

Page 14

Lun

VVName

HostName

-Host_WWN/iSCSI_Name-

Port Type

0

srm_vol1

pe2970-20

21000024FF223A1B

1:1:2 host

0

srm_vol1

pe2970-20

21000024FF223A1A

0:1:2 host

-------------------------------------------------------

2total

8.Discover the LUNs on the ESX(i) hosts.

9.After exporting the VLUNs to the ESX(i) host, rescan the HBA to verify if the VLUN is now visible to the ESX(i) host.

10.Create a VMFS Datastore.

11.Deploy VMs per your requirements on the protected site.

Configuring Remote Copy with IP between the protected and recovery sites

HP 3PAR Remote Copy Software provides the capability to copy virtual volumes from the protected site HP 3PAR storage system to the recovery site HP 3PAR Storage system.

Ensure that the HP 3PAR storage system hardware is set up appropriately for creating a Remote Copy configuration between the protected site and recovery site.

NOTE: SRM works with a Remote Copy setup using IP or Fibre Channel connectivity. This document describes the steps required to configure Remote Copy with IP. For more information about implementing Remote Copy over Fibre Channel, see the HP 3PAR Remote Copy Software User's Guide.

Initial setup for Remote Copy from the Protected Site

1.From the protected site (s230 in the following examples) set up the Gigabit Ethernet link.

root@inodee2023:~# controlport rcip addr -f 10.100.33.88 255.255.255.0 0:9:1 Remote Copy interface change successful.

root@inodee2023:~# controlport rcip addr -f 10.101.33.88 255.255.255.0 1:9:1 Remote Copy interface change successful.

root@inodee2023:~# controlport rcip gw -f 10.100.33.1 0:9:1 Remote Copy interface change successful.

root@inodee2023:~# controlport rcip gw -f 10.101.33.1 1:9:1 Remote Copy interface change successful.

2.Verify connectivity (s230).

root@inodee2023:~# showport -rcip

 

 

 

 

N:S:P State ---HwAddr---

IPAddr

Netmask

Gateway MTU

Rate Duplex

AutoNeg

 

 

 

 

 

0:9:1 ready 0002AC8014A5 10.100.33.88 255.255.255.0 10.100.33.1 1500

1Gbps

Full

Yes

 

 

 

 

 

1:9:1 ready 0002AC80149F 10.101.33.88 255.255.255.0 10.101.33.1 1500

1Gbps

Full

Yes

-----------------------------------------------------------------------------------------

2

14 HP 3PAR storage system setup

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Abstract Warranty Contents Introduction VMware vCenter Site Recovery Manager overview VMware vCenter Site Recovery Manager overview Supported configurations HP 3PAR SRA installation and configuration prerequisites Verifying installation Installing HP 3PAR SRAInstalling HP 3PAR SRA Removing HP 3PAR SRAHP 3PAR storage system setup Page 12 HP 3PAR storage system setup Create virtual volumes on the protected and recovery sites Initial setup for Remote Copy from the Protected Site Verify connectivity s230Initial setup for Remote Copy from the Recovery Site Setting up Remote Copy targets and linksAdding a Virtual Volume to existing Remote Copy groups Creating Synchronous Remote Copy groupsDisplaying the Remote Copy groups configuration Configuring VMware vCenter Site Recovery Manager HP 3PAR SRAConfiguring HP 3PAR SRA Page SLD configuration Validating HP 3PAR StoreServ Storage SSL certificatesPage Recovery Recovery and failbackClean Up TestReprotect Page Options HP 3PAR SRA for the VMware SRM 5.5 utilitySyntax Cleanstate Partial licensing Remote Copy failover from Site a to Site B GethostRemote Copy recover Replication begins from Site B to Site a Remote Copy restore role back without sync NostartRemote Copy sync from Site a to Site B Test failover workflowSRMROVVID, SRMRWVVID, SRMRECOVERROVVID, Special notesSrmtargetbkrovvid Primary Array is down or is taken offline SGT Support for multiple array pair configuration Support for virtual volume sets and host setsSupport for SLD Workarounds for SLD error codesLimitations of SLD configuration Support for SLD HP 3PAR documentation Support and other resourcesContacting HP Documentation listTroubleshooting Guide Required Typographic conventionsHP 3PAR branding information Document conventionsDocumentation feedback

System Replication Adapter Software QL227 for VMware specifications

HP System Replication Adapter Software QL227 for VMware is a sophisticated tool designed to enhance data protection and availability for virtualized environments. This software enables seamless replication of virtual machines (VMs) across different locations, ensuring business continuity even in the face of disasters or system failures.

One of the main features of QL227 is its ability to integrate tightly with VMware environments. It supports VMware vSphere, which is a leading virtualization platform, allowing users to leverage their existing infrastructure while benefiting from HP’s data replication technology. The adapter simplifies the process of setting up and managing replication tasks, which can be critical for organizations with stringent uptime requirements.

Another notable characteristic of the HP System Replication Adapter is its support for block-level replication. This technology ensures that only the changed data blocks are transferred to the secondary site, optimizing bandwidth usage and minimizing the impact on system performance. This feature is especially valuable for businesses that operate in environments with limited network capacity.

QL227 also includes advanced monitoring and reporting capabilities. Administrators can easily track the status of replication tasks, with real-time notifications and insights that help ensure data integrity and availability. Additionally, the software offers various recovery options, allowing users to initiate failover or failback processes with minimal disruption to operations.

The adapter’s compatibility with HP’s Enterprise Virtual Array (EVA) storage systems enhances its functionality even further, providing a robust infrastructure for managing replicated data. It is designed to work in conjunction with HP’s other data protection solutions, creating a comprehensive strategy for safeguarding critical business information.

Moreover, HP System Replication Adapter Software QL227 features automated policy management, which simplifies the administration of data replication tasks. This allows organizations to set predefined rules for how, when, and where data should be replicated, reducing the risk of human error and ensuring consistency across environments.

In conclusion, the HP System Replication Adapter Software QL227 for VMware is an essential solution for businesses looking to improve their data replication processes. Its integration with VMware, efficient block-level replication, advanced monitoring capabilities, and compatibility with HP storage systems make it a powerful tool for enhancing data protection and ensuring business continuity. With its innovative features and user-friendly interface, QL227 stands out as a vital component for any organization aiming to secure their virtualized infrastructure.
Top Page Image Contents