HP System Replication Adapter Software QL227 for VMware Primary Array is down or is taken offline

Page 35

3.Issue the removetask –d <TaskID> command to remove the task detail.

4.Rerun the SRM operation again.

If you have multiple failed virtual volumes in the group, you may need to repeat steps 1 through 4 for all volumes.

•For HP 3PAR OS versions up to 3.1.2 MU2:

◦

◦

SRM supports only one-to-one replication. If one of the pair in an SLD setup is selected for an SRM configuration, only the selected pair will be started after re-protect in failover workflow.

Before failback, all the pairs in the SLD setup needs to be started as the requirement for setrcopygroup restore operation. You can run the showrcopy groups <groupname> command to see the status of the SLD groups. All the virtual volume members in the SLD setup has to be in Synced status for failback operation to be successful.

•Primary Array is down or is taken offline:

When the primary array is down or the remote copy link between the primary and secondary array is down, and if you need to run the recovery operation, then perform the follow steps:

1.Click Disaster Recovery with Forced Recovery to execute the recovery.

After completing this step, SRM displays the Recovery Required prompt. This implies that after bringing the storage array or link up, you must run the recovery again.

2.After bringing the storage array or link up, navigate to the Devices tab in SRM and click Refresh to rediscover the devices.

Make sure that the devices are discovered again in SRM.

3.Execute the Recovery and Reprotect operations.

For more information about Disaster Recovery—Forced Recovery option, see the VMware vCenter Site Recovery Manager documentation.

•If the same virtual volume IDs are part of a single RC group across two storage arrays that are part of an SRM array pair, then during failback reprotect operation SRM service might stop. To avoid this issue, maintain unique ids for the virtual volumes in the RC group across the storage arrays.

For Example:

Run the showrcopy command from the HP 3PAR CLI interface. The output for one of the RC Groups is as follows:

showrcopy

Group Information

Name

Target

Status

Role

 

Mode

Options

 

TestRCG

rsra

Started

Primary

Periodic Last-Sync 2014-10-20 12:44:24

SGT , over_per_alert

 

 

 

 

 

LocalVV

ID

RemoteVV

ID

 

SyncStatus

LastSyncTime

TestVV_Pri.0 1741

TestVV_Sec.0 1740

Synced

2014-10-20

12:44:24 SGT

TestVV_Pri.1 1742

TestVV_Sec.1 1741

Synced

2014-10-20

12:44:24 SGT

As displayed in the above result, the virtual volume id 1741 is same between the primary and secondary volumes in the same RC group. In an RC Group, none of the virtual volumes should have the same virtual volume ID.

35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Abstract Warranty Contents Introduction VMware vCenter Site Recovery Manager overview VMware vCenter Site Recovery Manager overview Supported configurations HP 3PAR SRA installation and configuration prerequisites Removing HP 3PAR SRA Installing HP 3PAR SRAInstalling HP 3PAR SRA Verifying installationHP 3PAR storage system setup Page 12 HP 3PAR storage system setup Create virtual volumes on the protected and recovery sites Verify connectivity s230 Initial setup for Remote Copy from the Protected SiteSetting up Remote Copy targets and links Initial setup for Remote Copy from the Recovery SiteCreating Synchronous Remote Copy groups Adding a Virtual Volume to existing Remote Copy groupsDisplaying the Remote Copy groups configuration HP 3PAR SRA Configuring VMware vCenter Site Recovery ManagerConfiguring HP 3PAR SRA Page Validating HP 3PAR StoreServ Storage SSL certificates SLD configurationPage Test Recovery and failbackClean Up RecoveryReprotect Page Options HP 3PAR SRA for the VMware SRM 5.5 utilitySyntax Cleanstate Partial licensing Gethost Remote Copy failover from Site a to Site BRemote Copy recover Replication begins from Site B to Site a Nostart Remote Copy restore role back without syncTest failover workflow Remote Copy sync from Site a to Site BSpecial notes SRMROVVID, SRMRWVVID, SRMRECOVERROVVID,Srmtargetbkrovvid Primary Array is down or is taken offline SGT Support for virtual volume sets and host sets Support for multiple array pair configurationSupport for SLD Workarounds for SLD error codesLimitations of SLD configuration Support for SLD Documentation list Support and other resourcesContacting HP HP 3PAR documentationTroubleshooting Guide Document conventions Typographic conventionsHP 3PAR branding information RequiredDocumentation feedback

System Replication Adapter Software QL227 for VMware specifications

HP System Replication Adapter Software QL227 for VMware is a sophisticated tool designed to enhance data protection and availability for virtualized environments. This software enables seamless replication of virtual machines (VMs) across different locations, ensuring business continuity even in the face of disasters or system failures.

One of the main features of QL227 is its ability to integrate tightly with VMware environments. It supports VMware vSphere, which is a leading virtualization platform, allowing users to leverage their existing infrastructure while benefiting from HP’s data replication technology. The adapter simplifies the process of setting up and managing replication tasks, which can be critical for organizations with stringent uptime requirements.

Another notable characteristic of the HP System Replication Adapter is its support for block-level replication. This technology ensures that only the changed data blocks are transferred to the secondary site, optimizing bandwidth usage and minimizing the impact on system performance. This feature is especially valuable for businesses that operate in environments with limited network capacity.

QL227 also includes advanced monitoring and reporting capabilities. Administrators can easily track the status of replication tasks, with real-time notifications and insights that help ensure data integrity and availability. Additionally, the software offers various recovery options, allowing users to initiate failover or failback processes with minimal disruption to operations.

The adapter’s compatibility with HP’s Enterprise Virtual Array (EVA) storage systems enhances its functionality even further, providing a robust infrastructure for managing replicated data. It is designed to work in conjunction with HP’s other data protection solutions, creating a comprehensive strategy for safeguarding critical business information.

Moreover, HP System Replication Adapter Software QL227 features automated policy management, which simplifies the administration of data replication tasks. This allows organizations to set predefined rules for how, when, and where data should be replicated, reducing the risk of human error and ensuring consistency across environments.

In conclusion, the HP System Replication Adapter Software QL227 for VMware is an essential solution for businesses looking to improve their data replication processes. Its integration with VMware, efficient block-level replication, advanced monitoring capabilities, and compatibility with HP storage systems make it a powerful tool for enhancing data protection and ensuring business continuity. With its innovative features and user-friendly interface, QL227 stands out as a vital component for any organization aiming to secure their virtualized infrastructure.
Top Page Image Contents