HP System Replication Adapter Software QL227 for VMware manual Sgt

Page 36

If you see this issue, do the following to resolve this issue:

◦Process 1

1.Identify all serial ID numbers on Primary_array and Secondary_array by running the showrcopy command in HP 3PAR CLI interface.

Sample output:

Primary_array Secondary_array

Group Information

Name

Target

Status

Role

 

Mode

Options

 

TestRCG

rsra

Started

Primary

Periodic Last-Sync 2014-10-20

12:44:24 SGT , over_per_alert

 

 

 

 

 

LocalVV

ID

RemoteVV

ID

SyncStatus

LastSyncTime

TestVV_Pri.0 1741

TestVV_Sec.0 1740

Synced

2014-10-20

12:44:24

SGT

 

 

 

 

 

 

 

TestVV_Pri.1 1742

TestVV_Sec.1 1741

Synced

2014-10-20

12:44:24

SGT

 

 

 

 

 

 

 

In the sample set of replications seen above, the serial ID 1741 is used on both arrays.

2.Stop the replication between Primary_array and Secondary_array by running the stoprcopygroup <group_name> command in HP 3PAR CLI interface for RC groups that have the same serialIDs used by source and target devices.

3.Destroy the target device (Secondary Virtual volume) TestVV_Sec.1 with serialID 1741 on Secondary_array.

4.Recreate the target device TestVV_Sec.1 on Secondary_array. The Secondary_array assigns a new serialID automatically. This new serialID, one above the largest serialID currently used by Secondary_array. For example, if the highest current serialID on Secondary_array is 400, the new device TestVV_Sec.1 assigned is serialID 401.

5.Ensure that the serialID of the new device TestVV_Sec.1 is not used by any device on Primary_array.

6.Re-establish the replication relationship between device TestVV_Pri.1 on Primary_array and device TestVV_Sec.1 on Secondary_array.

IMPORTANT: This solution destroys the designated target devices only. Do not make any changes to the source devices. However, if it is not possible to achieve uniqueness of serialIDs between the two Arrays, it might be necessary to recreate the source devices. To recreate source devices safely, migrate the data to new storage devices before the source (Primary_array) device is destroyed.

◦Process 2

Create a series of small volumes that are sufficient to bring the serialIDs list out of sync between the two Sites. For example:

1.Ensure that Primary_array has serialIDs starting from 250.

2.Ensure that Secondary_array has serialIDs starting from 240.

3.Create 30 to 40 small volumes or devices on Primary_array to use all the indexes from 250 to 280.

4.Delete these small volumes or devices which also delete these serialIDs.

NOTE: The next serialID on Primary_array would be 281 and thus preventing any duplication.

36 Special notes

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Abstract Warranty Contents Introduction VMware vCenter Site Recovery Manager overview VMware vCenter Site Recovery Manager overview Supported configurations HP 3PAR SRA installation and configuration prerequisites Installing HP 3PAR SRA Installing HP 3PAR SRAVerifying installation Removing HP 3PAR SRAHP 3PAR storage system setup Page 12 HP 3PAR storage system setup Create virtual volumes on the protected and recovery sites Initial setup for Remote Copy from the Protected Site Verify connectivity s230Initial setup for Remote Copy from the Recovery Site Setting up Remote Copy targets and linksAdding a Virtual Volume to existing Remote Copy groups Creating Synchronous Remote Copy groupsDisplaying the Remote Copy groups configuration Configuring VMware vCenter Site Recovery Manager HP 3PAR SRAConfiguring HP 3PAR SRA Page SLD configuration Validating HP 3PAR StoreServ Storage SSL certificatesPage Recovery and failback Clean UpRecovery TestReprotect Page HP 3PAR SRA for the VMware SRM 5.5 utility SyntaxOptions Cleanstate Partial licensing Remote Copy failover from Site a to Site B GethostRemote Copy recover Replication begins from Site B to Site a Remote Copy restore role back without sync NostartRemote Copy sync from Site a to Site B Test failover workflowSRMROVVID, SRMRWVVID, SRMRECOVERROVVID, Special notesSrmtargetbkrovvid Primary Array is down or is taken offline SGT Support for multiple array pair configuration Support for virtual volume sets and host setsWorkarounds for SLD error codes Limitations of SLD configurationSupport for SLD Support for SLD Support and other resources Contacting HPHP 3PAR documentation Documentation listTroubleshooting Guide Typographic conventions HP 3PAR branding informationRequired Document conventionsDocumentation feedback

System Replication Adapter Software QL227 for VMware specifications

HP System Replication Adapter Software QL227 for VMware is a sophisticated tool designed to enhance data protection and availability for virtualized environments. This software enables seamless replication of virtual machines (VMs) across different locations, ensuring business continuity even in the face of disasters or system failures.

One of the main features of QL227 is its ability to integrate tightly with VMware environments. It supports VMware vSphere, which is a leading virtualization platform, allowing users to leverage their existing infrastructure while benefiting from HP’s data replication technology. The adapter simplifies the process of setting up and managing replication tasks, which can be critical for organizations with stringent uptime requirements.

Another notable characteristic of the HP System Replication Adapter is its support for block-level replication. This technology ensures that only the changed data blocks are transferred to the secondary site, optimizing bandwidth usage and minimizing the impact on system performance. This feature is especially valuable for businesses that operate in environments with limited network capacity.

QL227 also includes advanced monitoring and reporting capabilities. Administrators can easily track the status of replication tasks, with real-time notifications and insights that help ensure data integrity and availability. Additionally, the software offers various recovery options, allowing users to initiate failover or failback processes with minimal disruption to operations.

The adapter’s compatibility with HP’s Enterprise Virtual Array (EVA) storage systems enhances its functionality even further, providing a robust infrastructure for managing replicated data. It is designed to work in conjunction with HP’s other data protection solutions, creating a comprehensive strategy for safeguarding critical business information.

Moreover, HP System Replication Adapter Software QL227 features automated policy management, which simplifies the administration of data replication tasks. This allows organizations to set predefined rules for how, when, and where data should be replicated, reducing the risk of human error and ensuring consistency across environments.

In conclusion, the HP System Replication Adapter Software QL227 for VMware is an essential solution for businesses looking to improve their data replication processes. Its integration with VMware, efficient block-level replication, advanced monitoring capabilities, and compatibility with HP storage systems make it a powerful tool for enhancing data protection and ensuring business continuity. With its innovative features and user-friendly interface, QL227 stands out as a vital component for any organization aiming to secure their virtualized infrastructure.
Top Page Image Contents