HP AdvanceStack Internet Router manual Connecting a Modem to the Auxiliary Port

Page 29

Installing the HP AdvanceStack Internet Router

Connecting to the Network

Connecting a Modem to the Auxiliary Port

Take the following steps to connect a modem to the auxiliary port on the router:

1.Use an RJ-45 roll-over cable with an RJ-45-to-DB-25 or RJ-45-to-DB-9 adapter to connect a modem to the auxiliary port. The adapters provided by HP are labeled “Modem”.

Installation

Figure 2-4.Connecting a Modem to the Auxiliary Port

2.Make sure that your modem and the auxiliary port on the router are configured for the same transmission speed (38400 baud is typical) and hardware flow control with Data Carrier Detect (DCD) and Data Terminal Ready (DTR) operations.

2-13

Image 29
Contents HP AdvanceStack Internet Router Page Support is as close As the World Wide Web Additional HP Support Services HP AdvanceStack Internet Router Installation GuidePublication Number Contents Verifying Network Connectivity Getting More Information Configuring the HP AdvanceStack Internet RouterCable Specifications Page HP AdvanceStack Internet Router Overview HP AdvanceStack Internet Router Overview Hardware FeaturesSoftware Features Compression Includes switchingCables and Adapters Ordering InformationCisco Systems Contact Information Documentation and SoftwareCisco Systems, Inc West Tasman Drive San Jose, CA Tel Nets FaxVerifying Included Parts InstallationInstalling the HP AdvanceStack Internet Router Modem for remote access optionalRequired Tools and Parts Preparing to Connect to a NetworkIsdn Connections Isdn BRI Cable Specifications S/T CableSpecification High-Capacitance Cable Low-Capacitance Cable Device Type Gender Typical Devices Synchronous Serial ConnectionsTypical DTE and DCE Devices Data Rate Baud Distance Feet Distance Meters Or other DCE deviceEIA/TIA-232 Speed and Distance Limitations U T I O N Console and Auxiliary Port ConsiderationsConsole Port Connections Circuitry on the boards Installing the ModuleWhile you are installing the module Installation Connecting to a WAN Connecting to the NetworkConnecting the Isdn BRI Port to an NT1 Device Connecting the Console Terminal and ModemConnecting the Console Terminal Connecting a Modem to the Auxiliary Port What to Do After Installing the Router Hardware Configuration Booting the Router for the First TimeConfiguring the HP AdvanceStack Internet Router Configuring the Router for the First TimeBegin to configure the router Using the System Configuration Dialog Reflect the screen displays on your console Parity, and 2 stop bitsOn the console screen OK? Enter the enable and virtual terminal passwords Enter an enable secret passwordCountry Isdn Switch Type Description Isdn Switch TypePress Return or enter yes to configure serial port Configuring Ethernet or VG InterfacesConfiguration Prompt changes to the privileged Exec prompt Using Configuration ModeRouter will now boot with the configuration you entered Using AutoInstallCisco IOS Modes of Operation Cisco IOS Software BasicsCisco IOS Operating Modes Mode Usage How to Enter the Mode Prompt OperationInterface serial 0 command to Getting Context-Sensitive Help Saving Configuration Changes Configuring IsdnRouter config# username targetrouter password abc Enter the exit command to exit interface configuration mode Enter the exit command to exit global configuration mode Example Isdn ConfigurationRouter# config term Example Isdn ConfigurationGetting More Information ConfigurationVerifying Network Connectivity Reading the LEDs MaintenanceState Description TroubleshootingLEDs on the Host Device Front Panel Isdn BRI LEDs on the HP AdvanceStack Internet Router Front PanelRecovering Lost Passwords Upgrading the Boot ROMsBoot ROMs and ignore Nvram Signal to the routerEnter the initialize command to initialize the router Ration Dialog appearsAre different Passwords, if they are not encrypted, and proceed to stepNvram Or replace a password, proceed to and log Press Ctrl-Z to exit configuration modeReboot the router Configuration register value you set in step0x2102 is a combination of settings Virtual Configuration Register SettingsVirtual Configuration Register Bit Meanings Bit No.a Hexadecimal MeaningVirtual configuration register is stored in Nvram Changing Configuration Register SettingsExplanation of Boot Field Configuration Register Bits 00 to Boot Field Boot ProcessVirtual Configuration Register Bit Meanings Boot field number, a hyphen, and the processor type Default Boot FilenamesOverrides the default boot filename Action or Filename BitBaud Bit Bit Address net hostCopying a Cisco IOS Image to Flash Memory Enabling Booting from Flash MemoryFollowing messages display Command reference publications System reboots using the new image in Flash memoryBack of HP Switching Hub Inserting the HP Internet Router Module into an HP Remote 2C Router to Router Connections Cable Specifications Console and Auxiliary Port Signals PinoutsIdentifying a Roll-Over Cable Cable SpecificationsConsole Port Signals and Pinouts Figure A-2. Connecting the Auxiliary Port to a Modem Auxiliary Port Signals and PinoutsEIA-530 Synchronous Serial Cable Assemblies and PinoutsFigure A-3. EIA-530 Serial Cable Assembly Direction 60 Pin Signal 25 Pin DTE DCEaTable A-4.EIA-530 DTE Cable Pinouts DB-60 to DB-25 EIA/TIA-232 Table A-5. EIA/TIA-232 DCE Cable Pinouts DB-60 to DB-25 60 Pin Signal Description Direction 25 PinCable Table A-6. EIA/TIA-232 DCE Cable Pinouts DB-60 to DB-25EIA/TIA-449 Table A-7. EIA/TIA-449 DTE Cable Pinouts DB-60 to DB-37 60 Pin Signal Description Direction 37 PinTable A-8. EIA/TIA-449 DCE Cable Pinouts DB-60 to DB-37 Indicates DTE to DCE, and indicates DCE to DTE Figure A-6. V.35 Cable AssemblyTable A-9. V.35 DTE Cable Pinouts DB-60 to 34-Pin 60 Pin Signal Description Direction 34 PinCable Table A-10. V.35 DCE Cable Pinouts DB-60 to 34-PinFigure A-7. X.21 Cable Assembly Cable Specifications Table A-11. X-21 DTE Cable Pinouts DB-60 to DB-15 60 Pin Signal Description Direction 15 PinTable A-12. X.21 DCE Cable Pinouts DB-60 to DB-15 RJ-45 TE b NT c Polarity Pin a Isdn BRI Port and Cable PinoutsTable A-13. BRI Port RJ-45 Pinout HP J3138A Specifications Power ConsumptionPhysical EnvironmentalIEC 950 1991 + A1, A2 / .EN60950 I 1992 + A1, A2 ConnectorsElectromagnetic Safety Information Safety and Regulatory StatementsInformations concernant la sécurité Safety and Regulatory StatementsHinweise zur Sicherheit SicherheitssymboleSimboli di sicurezza Considerazioni sulla sicurezzaSímbolos de seguridad Consideraciones sobre seguridadStatements Safety Information JapaneseRegulatory Statements No repairs can be done by the customer Unshielded cables and EN55022 European CommunityCanada Page Index IndexIndex See also Isdn BRI Setup Page Page J3138-90003