HP AdvanceStack Internet Router manual Ok?

Page 35

Configuring the HP AdvanceStack Internet Router

Configuring the Router for the First Time

1 ISDN Basic Rate interface.

32K bytes of non-volatile configuration memory.

8192K bytes of processor board System flash (Read ONLY)

Notice: NVRAM invalid, possibly due to write erase.

--- System Configuration Dialog ---

At any point you may enter a question mark '?' for help. Refer to the 'Getting Started' Guide for additional help. Use ctrl-c to abort configuration dialog at any prompt.

Default settings are in square brackets '[]'.

Would you like to enter the initial configuration dialog? [yes]:

3.Press Return or enter yes to begin the configuration process.

4.When the System Configuration Dialog asks whether you want to view the current interface summary, press Return or enter yes:

First, would you like to see the current interface summary? [yes]:

Any interface listed with OK? value “NO” does not have a valid configuration

Interface*	IP-Address	OK?	Method		Status	Protocol
Ethernet0	unassigned	NO	not set		up	down
BRI0	unassigned	NO	not set		up	up
Serial0	unassigned	NO	not	set	down	down
Serial1	unassigned	NO	not	set	down	down

*If you are attached to a VG device, you will see the specification for VG0

5.Configure the global parameters. A typical configuration follows:

Configuring global parameters:

Enter host name [Router]:

Next, you are prompted to enter an enable secret password. There are two types of privileged-level passwords:

•Enable secret password (a very secure, encrypted password)

•Enable password (a less secure, nonencrypted password)

The enable password is used when the enable secret password does not exist.

For maximum security, be sure the passwords are different. If you enter the same password for both, the router will not accept your entry.

Configuration

3-5

Image 35

Contents HP AdvanceStack Internet Router Page Support is as close As the World Wide Web Additional HP Support Services HP AdvanceStack Internet Router Installation GuidePublication Number Contents Verifying Network Connectivity Getting More Information Configuring the HP AdvanceStack Internet RouterCable Specifications Page HP AdvanceStack Internet Router Overview HP AdvanceStack Internet Router Overview Hardware FeaturesSoftware Features Compression Includes switchingCables and Adapters Ordering InformationTel Nets Fax Documentation and SoftwareCisco Systems Contact Information Cisco Systems, Inc West Tasman Drive San Jose, CAVerifying Included Parts InstallationPreparing to Connect to a Network Modem for remote access optionalInstalling the HP AdvanceStack Internet Router Required Tools and PartsIsdn Connections Isdn BRI Cable Specifications S/T CableSpecification High-Capacitance Cable Low-Capacitance Cable Device Type Gender Typical Devices Synchronous Serial ConnectionsTypical DTE and DCE Devices Data Rate Baud Distance Feet Distance Meters Or other DCE deviceEIA/TIA-232 Speed and Distance Limitations U T I O N Console and Auxiliary Port ConsiderationsConsole Port Connections Circuitry on the boards Installing the ModuleWhile you are installing the module Installation Connecting to a WAN Connecting to the NetworkConnecting the Isdn BRI Port to an NT1 Device Connecting the Console Terminal and ModemConnecting the Console Terminal Connecting a Modem to the Auxiliary Port What to Do After Installing the Router Hardware Configuration Booting the Router for the First TimeConfiguring the HP AdvanceStack Internet Router Configuring the Router for the First TimeBegin to configure the router Using the System Configuration Dialog Reflect the screen displays on your console Parity, and 2 stop bitsOn the console screen OK? Enter the enable and virtual terminal passwords Enter an enable secret passwordCountry Isdn Switch Type Description Isdn Switch TypePress Return or enter yes to configure serial port Configuring Ethernet or VG InterfacesConfiguration Prompt changes to the privileged Exec prompt Using Configuration ModeRouter will now boot with the configuration you entered Using AutoInstallCisco IOS Modes of Operation Cisco IOS Software BasicsCisco IOS Operating Modes Mode Usage How to Enter the Mode Prompt OperationInterface serial 0 command to Getting Context-Sensitive Help Saving Configuration Changes Configuring IsdnRouter config# username targetrouter password abc Enter the exit command to exit interface configuration mode Enter the exit command to exit global configuration mode Example Isdn ConfigurationRouter# config term Example Isdn ConfigurationGetting More Information ConfigurationVerifying Network Connectivity Reading the LEDs MaintenanceState Description TroubleshootingLEDs on the Host Device Front Panel Isdn BRI LEDs on the HP AdvanceStack Internet Router Front PanelRecovering Lost Passwords Upgrading the Boot ROMsRation Dialog appears Signal to the routerBoot ROMs and ignore Nvram Enter the initialize command to initialize the routerAre different Passwords, if they are not encrypted, and proceed to stepNvram Configuration register value you set in step Press Ctrl-Z to exit configuration modeOr replace a password, proceed to and log Reboot the routerBit No.a Hexadecimal Meaning Virtual Configuration Register Settings0x2102 is a combination of settings Virtual Configuration Register Bit MeaningsBoot Field Boot Process Changing Configuration Register SettingsVirtual configuration register is stored in Nvram Explanation of Boot Field Configuration Register Bits 00 toVirtual Configuration Register Bit Meanings Action or Filename Bit Default Boot FilenamesBoot field number, a hyphen, and the processor type Overrides the default boot filenameBaud Bit Bit Address net hostCopying a Cisco IOS Image to Flash Memory Enabling Booting from Flash MemoryFollowing messages display Command reference publications System reboots using the new image in Flash memoryBack of HP Switching Hub Inserting the HP Internet Router Module into an HP Remote 2C Router to Router Connections Cable Specifications Console and Auxiliary Port Signals PinoutsIdentifying a Roll-Over Cable Cable SpecificationsConsole Port Signals and Pinouts Figure A-2. Connecting the Auxiliary Port to a Modem Auxiliary Port Signals and PinoutsEIA-530 Synchronous Serial Cable Assemblies and PinoutsFigure A-3. EIA-530 Serial Cable Assembly Direction 60 Pin Signal 25 Pin DTE DCEaTable A-4.EIA-530 DTE Cable Pinouts DB-60 to DB-25 EIA/TIA-232 Table A-5. EIA/TIA-232 DCE Cable Pinouts DB-60 to DB-25 60 Pin Signal Description Direction 25 PinCable Table A-6. EIA/TIA-232 DCE Cable Pinouts DB-60 to DB-25EIA/TIA-449 Table A-7. EIA/TIA-449 DTE Cable Pinouts DB-60 to DB-37 60 Pin Signal Description Direction 37 PinTable A-8. EIA/TIA-449 DCE Cable Pinouts DB-60 to DB-37 Indicates DTE to DCE, and indicates DCE to DTE Figure A-6. V.35 Cable AssemblyTable A-9. V.35 DTE Cable Pinouts DB-60 to 34-Pin 60 Pin Signal Description Direction 34 PinCable Table A-10. V.35 DCE Cable Pinouts DB-60 to 34-PinFigure A-7. X.21 Cable Assembly Cable Specifications Table A-11. X-21 DTE Cable Pinouts DB-60 to DB-15 60 Pin Signal Description Direction 15 PinTable A-12. X.21 DCE Cable Pinouts DB-60 to DB-15 RJ-45 TE b NT c Polarity Pin a Isdn BRI Port and Cable PinoutsTable A-13. BRI Port RJ-45 Pinout Environmental Power ConsumptionHP J3138A Specifications PhysicalIEC 950 1991 + A1, A2 / .EN60950 I 1992 + A1, A2 ConnectorsElectromagnetic Safety Information Safety and Regulatory StatementsInformations concernant la sécurité Safety and Regulatory StatementsHinweise zur Sicherheit SicherheitssymboleSimboli di sicurezza Considerazioni sulla sicurezzaSímbolos de seguridad Consideraciones sobre seguridadStatements Safety Information JapaneseRegulatory Statements No repairs can be done by the customer Unshielded cables and EN55022 European CommunityCanada Page Index IndexIndex See also Isdn BRI Setup Page Page J3138-90003