HP OMEN - 15t-5000 manual System board, Windows operating system

Page 40

System board

Component

Spare part number

 

 

System board equipped with an Intel Core i7-4710 processor (includes thermal grease and thermal pads)

 

 

 

Includes 16 GB of system memory and 4 GB of discrete graphics memory for use in models without the

788615-001

Windows operating system

 

 

 

Includes 16 GB of system memory and 4 GB of discrete graphics memory for use in models with Windows

788615-501

8.1 Standard

 

 

 

Includes 16 GB of system memory and 4 GB of discrete graphics memory for use in models with Windows

788615-601

8.1 Professional

 

 

 

Includes 8 GB of system memory and 4 GB of discrete graphics memory for use in models without the

788616-001

Windows operating system

 

 

 

Includes 8 GB of system memory and 4 GB of discrete graphics memory for use in models with Windows

788616-501

8.1 Standard

 

 

 

Includes 8 GB of system memory and 4 GB of discrete graphics memory for use in models with Windows

788616-601

8.1 Professional

 

 

 

Includes 8 GB of system memory and 2 GB of discrete graphics memory for use in models without the

788614-001

Windows operating system

 

 

 

Includes 8 GB of system memory and 2 GB of discrete graphics memory for use in models with Windows

788614-501

8.1 Standard

 

 

 

Includes 8 GB of system memory and 2 GB of discrete graphics memory for use in models with Windows

788614-601

8.1 Professional

 

 

 

Before replacing the system board, follow these steps:

1.Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.

2.Disconnect the power from the computer by unplugging the power cord from the computer.

3.Disconnect all external devices from the computer.

4.Remove the bottom cover (see Bottom cover on page 23).

5.Remove the battery (see Battery on page 31).

6.Remove the WLAN module (see WLAN module on page 26).

7.Remove the SSD module (see Solid-state drive (M.2) on page 28).

8.Remove the heat sink and fans (see Heat sink and fans on page 29).

Remove the system board:

1.Disconnect the following cables from the system board.

(1): Display cable

(2): Left speaker cable

(3): Power connector cable

(4): Left light assembly

(5): TouchPad cable

34 Chapter 5 Removal and replacement procedures for Authorized Service Provider parts

Image 40
Contents HP Omen Notebook PC Product notice Safety warning notice Iv Safety warning notice Table of contents Specifications Product description Power requirements Operating system PreinstalledServiceability End user replaceable parts Category DescriptionGetting to know your computer Finding your hardware and software informationLocating hardware Locating softwareComponent Description DisplayAssistant app Right side Rear Top TouchpadLights TIP You can customize the keyboard lightingButtons and speakers If the computer has stopped responding and WindowsKeys TIP You can customize these keys in HP Omen ControlLabels Illustrated parts catalog Computer major componentsComponent Power button board includes cableHeat sink and fans Miscellaneous parts Display assembly subcomponents Sequential part number listing Spare part number DescriptionSequential part number listing 788620-001 Webcam/microphone module Removal and replacement preliminary requirements Service considerationsTools required Grounding guidelinesPackaging and transporting guidelines Typical electrostatic voltage levels Relative humidity EventWorkstation guidelines Material Use Voltage protection level Computer replacement procedures Bottom coverPage Disconnecting the battery Disconnect the battery see Disconnecting the battery on Wlan moduleReverse this procedure to install the Wlan module Solid-state drive M.2 Description Spare part numberHeat sink and fans Page Battery Page TouchPad System board Windows operating systemPage Page Power button board Power connector cable Speakers Light modules Display assembly Page Page Page Page Page Specifications Computer specificationsSolid-state drive specifications Inch display specificationsUpdating the Bios Starting Setup Utility BiosDetermining the Bios version Using HP PC Hardware Diagnostics Uefi Downloading a Bios updateDownloading HP PC Hardware Diagnostics Uefi to a USB device Creating recovery media and backups Backing up, restoring, and recoveringCreating HP Recovery media Restore and recovery Recovering using HP Recovery Manager What you need to knowRemoving the HP Recovery partition select models only Using HP Recovery media to recoverPower cord set requirements Requirements for all countriesRequirements for specific countries and regions Country/region Accredited agency Applicable note numberRequirements for specific countries and regions Recycling Bios IndexWlan Vents, identifying
Related manuals
Manual 76 pages 50.3 Kb Manual 8 pages 26.72 Kb