HP 3054A e All in One Inkjet CR237A#B1H manual Traditional wireless connection requires router

Page 34

Chapter 8

Traditional wireless connection (requires router)

To connect the HP All-in-One to an integrated wireless WLAN 802.11 network, you will need the following:

￿A wireless 802.11b/g/n network that includes a wireless router or access point.

NOTE: 802.11n will only support 2.4Ghz

￿A desktop computer or laptop with either wireless networking support, or a network interface card (NIC). The computer must be connected to the wireless network that you intend to install the HP All-in-One on.

￿Network name (SSID).

￿WEP key or WPA Passphrase (if needed).

To connect the product

1.Insert the product Software CD in the computer CD-ROM drive.

2.Follow the instructions on the screen.

When you are prompted, connect the product to the computer using the USB setup cable included in the box. Follow the onscreen prompts to enter your wireless network settings. The product will attempt to connect to the network. If the connection fails, follow the prompts to correct the problem, and then try again.

3.When the setup is finished, you will be prompted to disconnect the USB cable and test the wireless network connection. Once the product connects successfully to the network, install the software on each computer that will use the product over the network.

USB Connection (non-network connection)

The HP All-in-One supports a rear USB 2.0 High Speed port for connection to a computer.

NOTE: Web services will not be available with a USB direct connection.

To connect the product with the USB cable

▲Refer to the setup instructions that came with your product for information on connecting to a computer with a USB cable.

NOTE: Do not connect the USB cable to the product until you are prompted to do so.

If the printer software has been installed, the printer will operate as a plug and play device. If the software has not been installed, insert the CD that came with the device and follow the onscreen instructions.

Change from a USB connection to a wireless network

If you first setup your printer and installed the software with a USB cable, directly connecting the printer to your computer, you can easily change to a wireless network connection. You will need a wireless 802.11b/g/n network that includes a wireless router or access point.

NOTE: 802.11n will only support 2.4Ghz

Change from a USB connection to a wireless network

1.From the computer’s start menu select All Programs or Programs, and then select HP.

2.Select HP Deskjet 3050A J611 series

3.Select Printer Setup and Software Selection.

4.Select Convert a USB connected printer to wireless. Follow the onscreen instructions.

32 Connectivity

Page 33 Page 35
Image 34
Page 33 Page 35
Contents HP Deskjet 3050A J611 series Page Contents Regulatory notices How Do I? Chapter How Do I? Get to know the HP All-in-One Printer partsControl panel features Wireless SettingsFrom the Wireless Menu, select Settings Status LightsAuto Power-Off To change Auto Power-Off settingPrint photos PrintTo print a photo on photo paper Print documents To print a documentTips for print success Print Quick FormsPrint envelopes Print Quick FormsInk tips Printer settings tipsPaper loading tips Print using the maximum dpi To print in Maximum dpi modeChapter Print EPrint from anywhere EPrint from anywhereTo ePrint a document from anywhere Chapter EPrint from anywhere Paper basics Recommended papers for printingLoad media Load small-size paper Load envelopes Load media Chapter Paper basics Copy Copy and scanEasy Copy Scan to a computer More copy featuresPrepare the scan Scan from the printer control panel Scan from your computerTips for copy success Tips for scan successCheck the estimated ink levels Work with cartridgesOrder ink supplies Locate the cartridge number in the Printer Software Choose the right cartridgesReplace the cartridges Related topicsReplace the cartridges Use single-cartridge mode Cartridge warranty informationConnectivity Wi-Fi Protected Setup WPS requires WPS routerWireless Settings Menu method Push Button PBC methodChange from a USB connection to a wireless network Traditional wireless connection requires routerUSB Connection non-network connection Connect a new printer Change wireless network settingsTips for setting up and using a networked printer Advanced printer management tools for networked printersTo open the embedded Web server Improve print quality Solve a problemTo print a diagnostics To align the cartridges from the Printer SoftwareTo clear a paper jam To clean the cartridges automaticallyClear a paper jam Input trayOutput tray Inside of printerUnable to print Resolve print issuesTo verify that the product is set as the default printer Prevent paper jamsClear the print carriage Prepare the trays Ink cartridge problemPrinter failure Ink cartridge problem Networking If you have a problem, follow these stepsHP support Additional warranty options Chapter Solve a problem Technical information SpecificationsSystem requirements Environmental specifications Input tray capacityCopy specifications Paper weightsPrint specifications Scan specificationsEnvironmental product stewardship program Recycling program Power consumptionSleep mode HP inkjet supplies recycling programRegulatory notices Regulatory model identification number Products with wireless LAN devices European Union Regulatory NoticeRegulatory wireless statements FranceRegulatory notices Chapter Technical information Index
Top Page Image Contents