ASRock 990FX Extreme3 manual Acpi Configuration

Page 54

3.4.6 ACPI Configuration

Suspend to RAM

Use this item to select whether to auto-detect or disable the Suspend-to- RAM feature. Select [Auto] will enable this feature if the OS supports it.

Check Ready Bit

Use this item to enable or disable the feature Check Ready Bit.

Restore on AC/Power Loss

This allows you to set the power state after an unexpected AC/power loss. If [Power Off] is selected, the AC/power remains off when the power re- covers. If [Power On] is selected, the AC/power resumes and the system starts to boot up when the power recovers.

PS/2 Keyboard Power On

Use this item to enable or disable PS/2 keyboard to turn on the system from the power-soft-off mode.

PCI Devices Power On

Use this item to enable or disable PCI devices to turn on the system from the power-soft-off mode.

Ring-In Power On

Use this item to enable or disable Ring-In signals to turn on the system from the power-soft-off mode.

RTC Alarm Power On

Use this item to enable or disable RTC (Real Time Clock) to power on the system.

USB Keyboard/Remote Power On

Use this item to enable or disable the system to wake from S5 using USB Keyboard/Remote.

USB Mouse Power On

Use this item to enable or disable the system to wake from S5 using USB Mouse.

54

Image 54
Contents 990FX Extreme3 Copyright Notice DisclaimerContents Software Support Package Contents IntroductionSpecifications Unique Feature ConnectorBios Feature Rear Panel I/OCertifications HardwareMonitor See CautionPage Page Page Motherboard Layout I/O Panel LAN Port LED IndicationsTable for Audio Output Connection Page Installation Pre-installation PrecautionsCPU Installation Installation of CPU Fan and HeatsinkInstallation of Memory Modules Dimm Dual Channel Memory ConfigurationsInstalling a Dimm Installing an expansion card Expansion Slots PCI and PCI Express SlotsPcie Slots Slitm and Quad Slitm Operation Guide RequirementsDriver Installation and Setup For Windows XP / XP 64-bit OS For Slitm mode onlySelect Nvidia Control Panel tab Select Control Panel tabPage CrossFire Bridge Installing Three CrossFireXTM-Ready Graphics Cards CrossFireTM Bridge For Windows XP OS For Windows 7 / VistaTM OSSurround Display Feature \ Surround Display InformationJumpers Setup JumperSetting Clear Cmos JumperOnboard Headers and Connectors 5mm Audio CableInfrared Module Header This header supports an Chassis Speaker Header Please connect the chassis ATX Power Connector Ground pinATX 12V Power Connector Please connect an ATX 12V power supply to this connectorWhat is Hot Swap Function? Serial ATA3 SATA3 Hard Disks InstallationWhat is Hot Plug Function? Hot Plug and Hot Swap Functions for SATA3 HDDsSATA3 HDD Hot Plug Feature and Operation Guide Points of attention, before you process the Hot PlugHow to Hot Plug a SATA3 HDD Driver Installation Guide Installing Windows XP / XP 64-bit With RAID FunctionsSet up Uefi Use RAID Installation Guide to set RAID configuration \ RAID Installation Guide Make a SATA3 Driver DisketteInstalling Windows XP / XP 64-bit Without RAID Functions Untied Overclocking Technology Introduction Uefi Menu BarTo jump to the Exit Screen or exit the current screen Navigation KeysMain Screen System Time HourMinuteSecondOC Tweaker Screen Processor Maximum Frequency Dram Configuration Dram FrequencyAMD Turbo Core Technology North Bridge Maximum FrequencyCommand Rate CR Power Down EnableRAS# to CAS# Delay tRCD Write Recovery Time tWRVoltage Control Dram Voltage Would you like to save current setting user defaults?Four Activate Window tFAW NB VoltageAdvanced Screen Instant FlashCPU Configuration North Bridge Configuration Primary Graphics AdapterSouth Bridge Configuration Sata IDE Combined Mode Storage ConfigurationSata Mode Sata ControllerSerial Port Address Super IO ConfigurationSerial Port Infrared PortAcpi Configuration Acpi Hpet table USB 3.0 Controller USB ConfigurationUSB 2.0 Controller Legacy USB SupportChassis Fan 2 Setting CPU Fan 1 & 2 SettingChassis Fan 1 Setting Chassis Fan 3 SettingBoot Screen Security Screen Save Changes and Exit Load Uefi DefaultsExit Screen Discard Changes and ExitRunning The Support CD Install Operating SystemSupport CD Information Drivers MenuInstalling OS on a HDD Larger Than 2TB in Ahci Mode Installing OS on a HDD Larger Than 2TB in RAID Mode Drv4E CtrlB5 LangengChoose Usable Physical Drive List to select Raid HDD Page Windows VistaTM 64-bit Page Windows 7 64-bit
Related manuals
Manual 182 pages 34.52 Kb