GAS Conversion Instructions

MFH-I&S-02

1.Connect this water heater only to the type of gas (Natural or Propane gas) as shown on the rating plate. Use clean 1/2"black iron pipe. (Dirt and scale from the pipe can enter the combination control and cause it to malfunction). The inlet gas line must have a minimum length of 3" (7.6 cm) drip leg (sediment trap) installed as close to the water heater’s combination gas control as possible. A ground joint union must be installed in the gas supply line feeding the water heater to permit servicing of the water heater. Compounds used on the threaded joints of the gas piping must be resistant to the action of liquefied petroleum gases/propane gas.

2.This water heater and its gas connection must be leak tested before placing the water heater in operation. Check for gas leaks with a soap and water solution and a brush or a commercial leak detector fluid. NEVER USE A

MATCH OR OPEN FLAME FOR TESTING!

CAUTION

The water heater and individual shut-off valve must be disconnected from the gas supply piping system during any pressure testing of the system at test pressures in excess of ½ psi (3.5kPa). The water heater must be isolated from the gas supply piping system by closing its manual shut-off valve during any pressure testing of the gas supply system at test pressures equal to or less than ½ psi (3.5kPa). The supply line must be capped when not connected to the water heater.

This water heater has a gas control which will operate on either natural or liquefied petroleum (LP) gas. Normally the control is set to operate on natural gas, but can be converted for liquefied petroleum (LP) gas by following these instructions for gas conversion.

3.Change the pilot regulator by removing thermostat dial and pilot regulator

cap. Depress and rotate knob clockwise to the L.P. setting using a screwdriver. Replace cap.

4.Remove the outer door. Remove, or slide open, the inner door.

5.Disconnect thermocouple, Gas supply tube and pilot tube from the gas valve and remove the burner assembly from the water heater.

6.Remove main burner orifice and pilot assembly and replace with “RED” color coded L.P. orifice and pilot assembly provided in the cloth bag attached to the water heater.

CAUTION

All gas conversions must be performed by qualified service personnel only.

To convert from natural gas to LP gas

1.Depress and rotate gas main burner regulator knob clockwise to the “OFF” position.

2.Change main burner gas regulator by removing cap from gas regulator.

Depress and rotate knob counterclockwise	to the L.P. setting
using a screwdriver. Replace cap.

7.Replace the burner assembly and reconnect all fittings.

8.Close and/or replace inner and outer doors.

9.To light pilot, follow the lighting instructions provided on the water heater and in this installation and operation instruction manual.

To convert from LP to natural gas

1.Follow the instructions above except remove the “RED” main burner orifice and pilot assembly. Replace with the ones originally provided with the water heater.

2.Change the main gas regulator to “NAT” as noted in step 2 of the above instructions.

3.Change the pilot regulator to “NAT” as noted in step 3 of the above instructions.

GENERAL OPERATION

WARNING

Water heaters are heat producing appliances. To avoid damage or injury there shall be no materials stored against the water heater or vent-air intake system, and proper care shall be taken to avoid unnecessary contact (especially by children) with the water heater and vent-air intake system. UNDER NO

CIRCUMSTANCES SHALL FLAMMABLE MATERIALS, SUCH AS GASOLINE OR PAINT THINNER BE USED OR STORED IN THE VICINITY OF THIS WATER HEATER, VENT-AIR INTAKE SYSTEM OR IN ANY LOCATION FROM WHICH FUMES COULD REACH THE WATER HEATER OR VENT-AIR INTAKE SYSTEM.

MFH-I&S-02 specifications

The Lochinvar MFH-I&S-02 is a sophisticated Modular Floor Heat Integrated System known for its innovative design and efficiency in residential and commercial heating applications. As part of Lochinvar's commitment to providing high-performance solutions, the MFH-I&S-02 incorporates a variety of advanced technologies and characteristics that set it apart in the market.

One of the main features of the MFH-I&S-02 is its modular design, which allows for flexible installation options. This system can be easily tailored to meet the specific heating needs of any space, ensuring optimal comfort and energy efficiency. The modular approach not only simplifies installation but also enhances the system's versatility, making it suitable for both new constructions and retrofitting in existing buildings.

The MFH-I&S-02 employs an innovative heat exchanger that maximizes thermal efficiency. With a stainless steel construction, the heat exchanger is designed to withstand high temperatures and pressures, ensuring durability and longevity. This high-efficiency design translates to lower energy consumption, leading to cost savings for the end-user and a reduced carbon footprint.

In addition to its advanced heat exchanger, the MFH-I&S-02 includes smart controls and monitoring capabilities. These features enable users to easily manage their heating system through intuitive interfaces, whether via a wall-mounted display or a smartphone app. This connectivity allows for real-time monitoring and adjustments, facilitating proactive maintenance and optimization of heating performance.

The MFH-I&S-02 also utilizes variable speed technology in its pumps and fans, enhancing energy efficiency further. By adjusting operating speeds based on demand, the system minimizes unnecessary energy use while maintaining consistent heating. This adaptability not only improves comfort levels but also significantly contributes to overall system efficiency.

Furthermore, with a focus on sustainability, the MFH-I&S-02 is designed to work seamlessly with renewable energy sources, such as solar thermal systems. This integration capability allows it to maximize energy use from renewable sources, aligning with modern energy goals and regulations.

In summary, the Lochinvar MFH-I&S-02 is a cutting-edge heating solution that combines modular design, high-efficiency heat exchange, smart technology, and renewable energy compatibility. Its advancements in engineering and user-centered features make it an ideal choice for those seeking an effective and flexible heating system in today's energy-conscious environment.