ASRock P67 Pro manual System Panel Header

Page 24

System Panel Header

This header accommodates

(9-pin PANEL1)

several system front panel

(see p.11 No. 15)

functions.

Connect the power switch, reset switch and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.

PWRBTN (Power Switch):

Connect to the power switch on the chassis front panel. You may con gure the way to turn off your system using the power switch.

RESET (Reset Switch):

Connect to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart.

PLED (System Power LED):

Connect to the power status indicator on the chassis front panel. The LED is on when the system is operating. The LED keeps blinking when the sys- tem is in S1 sleep state. The LED is off when the system is in S3/S4 sleep state or powered off (S5).

HDLED (Hard Drive Activity LED):

Connect to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive is reading or writing data.

The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assign-ments are matched correctly.

Chassis Speaker Header

Please connect the chassis

(4-pin SPEAKER 1)

speaker to this header.

(see p.11 No. 14)

 

Power LED Header

(3-pin PLED1)

1

 

 

 

 

 

 

 

 

 

 

 

PLED-

(see p.11 No. 13)

 

 

 

PLED+

PLED+

 

Please connect the chassis power LED to this header to indicate system power status. The LED is on when the system is operating. The LED keeps blinking in S1 state. The LED is off in S3/S4 state or S5 state (power off).

24

Image 24
Contents P67 Pro Copyright Notice DisclaimerContents Uefi Setup Utility Package Contents IntroductionSpecifications Connector Bios FeatureUnique Feature Support CDHardware MonitorCertifications Page Page Motherboard Layout 20.3cm 8.0I/O Panel LAN Port LED IndicationsTable for Audio Output Connection Page Pre-installation Precautions Screw HolesCPU Installation Page Installation of CPU Fan and Heatsink Installation of Memory Modules Dimm Dual Channel Memory ConfigurationsInstalling a Dimm Notch break BreakInstalling an expansion card Expansion Slots PCI and PCI Express SlotsPcie slots Jumpers Setup DescriptionOnboard Headers and Connectors USB 2.0 Headers System Panel Header Chassis and Power Fan Connectors ATX Power ConnectorATX 12V Power Connector Please connect an ATX 12V power supply to this connectorSerial ATA3 SATA3 Hard Disks Installation What is Hot Plug Function? What is Hot Swap Function?Hot Plug and Hot Swap Functions for Sata / Sataii HDDs Hot Plug and Hot Swap Functions for SATA3 HDDsPoints of attention, before you process the Hot Plug How to Hot Plug a Sata / Sataii / SATA3 HDD Driver Installation Guide Installing Windows XP / XP 64-bit With RAID FunctionsSet up Bios Make a Sata / Sataii / SATA3 Driver DisketteSetting Up a RAID Ready System \ Intel Rapid Storage InformationMigrating a RAID Ready System to RAID 0, RAID 1 or RAID Use RAID Installation Guide to set RAID configuration Installing Windows XP / XP 64-bit Without RAID Functions Page Introduction Uefi Menu BarNavigation Keys Main ScreenTo jump to the Exit Screen or exit the current screen Advanced Screen ASRock Instant FlashCPU Configuration Active Processor Cores Hardware PrefetcherAdjacent Cache Line Prefetch Enhance Halt State C1EIntegrated Clock Chip Configuration Dram Configuration RAS to RAS Delay tRRD Write to Read Delay tWTRRead to Precharge tRTP Four Activate Window tFAWNorth Bridge Configuration South Bridge ConfigurationLow Mmio Align VT-dSouth Bridge Configuration Restore on AC/Power Loss PCI Legacy ModeVoltage Droop Adjust Deep SxStorage Configuration Sata ModeSata Controller Hard Disk S.M.A.R.TSuper IO Configuration OnBoard Floppy ControllerSerial Port Serial Port AddressVoltage Configuration Acpi Configuration USB Configuration USB 2.0 ControllerLegacy USB Support CPU Fan 1 & 2 Setting Chassis Fan 1 SettingChassis Fan 2 Setting Chassis Fan 3 SettingBoot Screen Security Screen Exit Screen Software Support Installing OS on a HDD Larger Than 2TB
Related manuals
Manual 245 pages 53.28 Kb