ASRock K7S41GX2 manual Connectors, Connector Description

Page 19

2.6 Connectors

Connectors are NOT jumpers. DO NOT place jumper caps over these connectors. Placing jumper caps over the connectors will cause perma- nent damage of the motherboard!

Connector

 

 

 

 

Figure

Description

FDD Connector

 

 

 

 

 

 

 

 

(33-pin FLOPPY1)

 

 

 

 

 

 

 

 

(see p.10 No. 15)

Pin1

FLOPPY1

 

the red-striped side to Pin1

Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the connector.

Primary IDE Connector (Blue)

Secondary IDE Connector (Black)

(39-pin IDE1, see p.10 No. 8)

(39-pin IDE2, see p.10 No. 7)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PIN1

IDE1

 

PIN1

IDE2

 

 

 

 

 

 

 

 

 

 

connect the blue end

 

 

connect the black end

 

to the motherboard

 

 

to the IDE devices

80-conductor, ATA 66/100/133 cable

Note: If you use only one IDE device on this motherboard, please set the IDE device as “Master”. Please refer to the instruction of your IDE device vendor for the details. Besides, to optimize compatibility and performance, please connect your hard disk drive to the primary IDE connector (IDE1, blue) and CD-ROM to the secondary IDE connector (IDE2, black).

USB 2.0 Connector

USB_PWR

(9-pin USB45)

P-5

P+5

 

GND

(see p.10 No. 17)

DUMMY

 

 

1

 

GND

 

P+4

 

P-4

 

USB_PWR

There are 4 default USB 2.0 ports on the rear panel. If the rear USB ports are not sufficient, this USB 2.0 connector is available to support 2 additional USB 2.0 ports.

Infrared Module Connector

(5-pin IR1)

(see p.10 No. 19)

1

IRTX +5V

DUMMY

GND

IRRX

This connector supports an optional wireless transmitting and receiving infrared module.

1 9

Image 19
Contents K7S41GX2 Disclaimer Copyright NoticeContents Software Support Introduction Package ContentsSpecifications Support CD Bios FeatureUnique Feature See CautionPage Page 19.8cm 7.8-in Motherboard LayoutLAN Port LED Indications I/O PanelPre-installation Precautions InstallationInstallation of CPU Fan and Heatsink CPU InstallationNotch break Installation of Memory Modules DimmExpansion Slots PCI, AMR, and AGP Slots Installing an expansion cardPS2USBPWR1 Jumpers SetupClear Cmos J1 Jumpers Connector Description ConnectorsFront Panel Audio Connector Driver Installation Guide Bios Menu Bar System Time HourMinuteSecond Navigation KeysMain Screen To jump to the Exit Screen or exit the current screenOC Tweaker Screen Vccm Voltage Intelligent Energy SaverDram Frequency Dram CAS LatencyAdvanced Screen CPU ConfigurationASRock Instant Flash V02.54 C Copyright 1985-2003, American Megatrends, Inc CPU ConfigurationChipset Configuration Acpi Configuration OnBoard IDE Controller Both Storage ConfigurationIDE Device Configuration Onboard IDE ControllerBlock Multi-Sector Transfer LBA/Large ModePIO Mode DMA ModePCI IDE BusMaster PCIPnP ConfigurationPCI Latency Timer Latency TimerSuper IO Configuration Floppy ConfigurationParallel Port IRQ Parallel Port ModeECP Mode DMA Channel EPP VersionUSB 2.0 Support USB ConfigurationUSB Controller Enabled USB ControllerHardware Health Event Monitoring Screen Boot Security ExitMain OC Tweaker Advanced Full Screen Logo Boot ScreenBoot Settings Configuration Boot LogoSecurity Screen Boot From Onboard LANBoot Up Num-Lock Change Supervisor PasswordExit Screen Drivers Menu Install Operating SystemSupport CD Information Running The Support CD

K7S41GX2 specifications

The ASRock K7S41GX2 is a motherboards that embodies an efficient balance of performance, compatibility, and value. It is designed to cater to the needs of budget-conscious users who seek robust capabilities without compromising on essential features. Built around the SiS 741GX chipset, this motherboard specifically targets the AMD socket A processors, supporting the AMD Athlon, Athlon XP, and Duron CPUs. This compatibility makes it an excellent choice for users looking to build or upgrade older systems.

One of the standout features of the ASRock K7S41GX2 is its affordability, making it a perfect entry-level solution for gamers and general users alike. The motherboard supports up to 2GB of DDR400 memory, providing ample capacity and speed for multitasking and running demanding applications. Additionally, the board boasts integrated graphics capabilities courtesy of the SiS Mirage 2 graphics engine, which offers sufficient graphical power for general computing and light gaming.

Another noteworthy attribute is the excellent expandability options. The K7S41GX2 comes equipped with multiple expansion slots, including one PCI Express x16 slot and three PCI slots, allowing users to add various cards such as dedicated graphics cards, sound cards, or network adapters to enhance their system's functionality. It also offers four SATA ports, which enable users to connect multiple modern storage devices, enhancing data transfer speeds and overall system performance.

Connectivity is further optimized with integrated Ethernet capabilities through a Realtek RTL8100C network controller, ensuring reliable network performance and internet access. Additionally, the board features several USB 2.0 ports, enabling users to connect a plethora of peripherals without hassle.

In terms of build quality, ASRock is known for its solid construction, ensuring longevity and reliability. The K7S41GX2 incorporates various safety features such as over-voltage protection and an anti-thunder design, which further enhances its durability in various environmental conditions.

Overall, the ASRock K7S41GX2 stands out as a versatile motherboard suitable for a range of users, from budget builders to those needing a solid foundation for basic computing tasks. Its combination of performance, expandability, and inherent technologies makes it an excellent choice for anyone looking to assemble or upgrade an affordable yet effective desktop system.