ASRock Version 2.3 manual Boot Settings Configuration, Security Screen, Boot From Onboard LAN

Page 57

3.5.1 Boot Settings Configuration

BIOS SETUP UTILITY

Boot

Boot Settings Configuration

Boot From Onboard LAN

[Disabled]

Bootup Num-Lock

[On]

To enable or disable the boot from onboard LAN feature.

 

Select Screen

 

Select Item

+ -

Change Option

F1

General Help

F9

Load Defaults

F10

Save and Exit

ESC

Exit

v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.

Boot From Onboard LAN

Use this item to enable or disable the Boot From Onboard LAN feature.

Boot Up Num-Lock

If this item is set to [On], it will automatically activate the Numeric Lock function after boot-up.

3.6 Security Screen

In this section, you may set or change the supervisor/user password for the system. For the user password, you may also clear it.

BIOS SETUP UTILITY

Main

Advanced

H/W Monitor

Boot

Security

Exit

Security Settings

Supervisor Password

: Not Installed

User Password

: Not Installed

Change Supervisor Password

Change User Password

Install or Change the password.

 

Select Screen

 

Select Item

Enter

Change

F1

General Help

F9

Load Defaults

F10

Save and Exit

ESC

Exit

v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.

5 7

Image 57
Contents ConRoeXFire-eSATA2 Disclaimer Copyright NoticeContents Software Support Bios Setup UtilityIntroduction Package ContentsSpecifications See Caution Bios FeatureSupport CD HardwarePage CPU For Windows 2000/XP/XP 64-bit/VistaTM/VistaTM64-bit 21.8cm 8.6 Motherboard LayoutTable for Audio Output Connection ASRock 8CHeSATAII I/OScrew Holes Pre-installation PrecautionsCPU Installation Page Installation of CPU Fan and Heatsink Dual Channel Memory Configurations Installation of Memory Modules DimmNotch break Installing a DimmInstalling an expansion card Expansion Slots PCI, PCI Express, and AGI Express SlotsAGI Express slot PCI Express CrossFireTM Operation Guide Enjoy the benefit of CrossFireTMWhat graphics cards work with CrossFireTM? DVI connector DMS View CrossFire TM Enable CrossFire TM Jumpers Setup Surround Display FeatureOnboard Headers and Connectors \ Surround Display InformationPrimary IDE connector Blue USB 2.0 Headers Front Panel Audio Header Ieee 1394 Headers HDMISPDIFHeader Hdmispdif Header Connection Guide ESATAII Interface Introduction What is eSATAII?Page Comparison between eSATAII and other devices Western Digital Sataii Hard Disk Setup GuidePage Driver Installation Guide What is Hot Plug Function?What is Hot Swap Function? Use RAID Installation Guide to set RAID configuration Set up BiosInstall Windows 2000 / XP / XP 64-bit OS on your system Make a Sata / Sataii Driver DisketteSetting Up a RAID Ready System Migrating a RAID Ready System to RAID RAID 1 or RAID Install Windows VistaTM / VistaTM 64-bit OS on your system Make a Sata / Sataii driver diskette Untied Overclocking Technology Bios Menu Bar Navigation Keys Main ScreenAdvanced Screen Boot Failure Guard CPU ConfigurationCPU Host Frequency Spread SpectrumRatio Actual Value Ratio Cmos SettingEnhance Halt State Max Cpuid Value LimitConfigure Dram Timing by SPD Chipset ConfigurationIntel R SpeedSteptm tech Dram FrequencyDram CAS# Latency Dram RAS# to CAS# DelayDram RAS# Precharge Dram RAS# Activate to PrechargeAcpi Configuration ATA/IDE Configuration IDE ConfigurationATA/IDE Configuration Combined OptionType PCIPnP Configuration Super IO Configuration Floppy ConfigurationOnBoard Floppy Controller Serial Port AddressECP Mode DMA Channel Parallel Port ModeParallel Port Address EPP VersionHardware Health Event Monitoring Screen USB ConfigurationUSB Controller USB 2.0 SupportTarget CPU Temperature C Boot ScreenCPU Quiet Fan Tolerance CBoot From Onboard LAN Boot Settings ConfigurationBoot Up Num-Lock Security ScreenExit Screen Load Optimal DefaultsSave Changes and Exit Discard Changes and ExitLGA 775 CPU Installation Live Demo Program Install Operating SystemSupport CD Information Running The Support CD