MSI G31M3-F - Motherboard - Micro ATX manual Advanced Bios Features

Page 44

BIOS Setup

Advanced BIOS Features

Full Screen LOGO Display

This item enables you to show the company logo on the bootup screen. Settings are:

[Enabled]

Shows a still image (logo) on the full screen at boot.

[Disabled]

Shows the POST messages at boot.

Quick Booting

Setting the item to [Enabled] allows the system to boot within 10 seconds since it will skip some check items.

Boot Up Num-Lock LED

This setting is to set the Num Lock status when the system is powered on. Setting to [On] will turn on the Num Lock key when the system is powered on. Setting to [Off] will allow users to use the arrow keys on the numeric keypad.

IOAPIC Function

This field is used to enable or disable the APIC (Advanced Programmable Interrupt Controller). Due to compliance with PC2001 design guide, the system is able to run in APIC mode. Enabling APIC mode will expand available IRQ resources for the system.

MPS Table Version

This field allows you to select which MPS (Multi-Processor Specification) version to be used for the operating system. You need to select the MPS version supported by your operating system. To find out which version to use, consult the vendor of your operating system.

Primary Graphics Adapter

This setting specifies which graphic card is your primary graphics adapter.

3-9

Image 44
Contents G31M3 series MS-7528 v1.X MainboardCopyright Notice TrademarksRevision History Technical SupportSafety Instructions Micro-Star International MS-7528 FCC-B Radio Frequency Interference StatementWeee Waste Electrical and Electronic Equipment Statement Page Vii Contents Appendix B Intel ICH7R Sata RAID Getting Started Getting StartedSata Mainboard SpecificationsIDE Connectors Getting Started FloppySlots Form FactorMainboard Layout G31M3 Series MS-7528 v1.X Micro-ATX MainboardPacking Checklist Hardware Setup Hardware SetupQuick Components Guide CPU Central Processing Unit Introduction to LGA 775 CPUCPU & Cooler Installation Lift the load lever up and open the load plate Locking switch DDR2 MemoryDual-Channel Memory Population Rules Installing Memory Modules Volt NotchPower Supply ATX 24-Pin Power Connector ATX1ATX 12V Power Connector JPW1 ATX1Back Panel LANAudio Ports Type a Audio Ports Type BConnectors Floppy Disk Drive Connector FDD1IDE Connector IDE1 FDD1Supported by ICH7/ICH7Roptional Serial ATA Connector SATA1 ~ SATA4SATA4 SATA3 SATA2 SATA1 Fan Power Connectors CPUFAN1, SYSFAN1~2 Chassis Intrusion Connector JCI1JSPD1 IEEE1394 Connector J13941 optionalPDIF-Out Connector JSPD1 Front Panel Connectors JFP1, JFP2 CD-In Connector CDIN1JFP2 JFP1 CDIN1Front Panel Audio Connector JAUD1 TPM Module connector JTPM1optionalJAUD1 JTPM1Front USB Connector JUSB1 ~ Serial Port Connector JcomJUSB1~2 USB 2.0 BracketJBAT1 JumperClear Cmos Jumper JBAT1 PCI Peripheral Component Interconnect Slots SlotsPCI Peripheral Component Interconnect Express Slots PCI Interrupt Request Routing Bios Setup Bios SetupEntering Setup Press DEL to enter SetupControl Keys Getting HelpGeneral Help F1 Main MenuMain Menu Exit Without Saving Bios Setup Load Optimized DefaultsSave & Exit Setup Standard Cmos Features Bios Setup Device / Vender / Size LBA/Large ModeDMA Mode Hard Disk S.M.A.R.TMS-7528 Mainboard System Information Advanced Bios Features Hpet TCG/TPM Support Integrated Peripherals Bios Setup On-Chip Sata Controller RAID ModeDevice Configuration Parallel Port ModeAcpi Standby State Power Management SetupAcpi Function Bios Setup Power Button Function Restore On AC Power LossWakeup Event Setup Resume by RTC AlarmCPU Smart FAN Target MonitorChassis Intrusion Cell Menu Advance Dram Configuration tRCD Advance Dram Configuration tRPAdvance Dram Configuration tRAS Advance Dram Configuration tRTPAdjust Channel 0/1 Drive MS-7528 Mainboard Load Fail-Safe/ Optimized Defaults Bios Setting Password Dual Core Center Activating Dual Core Center Dual Core Center MainIntroduction Sharp mode Smooth mode Clock DOT Dynamic OverClocking Clock Voltage FAN Speed Temperature User Profile Dual Core Center Intel ICH7R Sata RAID ICH7R Introduction Bios Configuration Using the Intel Matrix Stroage Manager Option ROMCreating, Deleting and Resetting RAID Volumes Intel ICH7R Sata RAIDCreate RAID Volume Intel ICH7R Sata RAID MS-7528 Mainboard Delete RAID Volume Reset Disks to Non-RAID Installing Software Install Driver in Windows XP† New Windows XP / 2000 Installation † Existing Windows XP/2000 Driver InstallationInstallation of Intel Matrix Storage Console Click on this itemIntel ICH7R Sata RAID MS-7528 Mainboard Intel ICH7R Sata RAID MS-7528 Mainboard RAID Migration Instructions Create RAID Volume from Existing Disk † RAID Level Intel ICH7R Sata RAID Configure Volume† RAID Volume Name † Strip Sizes Select the source diskIntel ICH7R Sata RAID Select Member Hard Drives MS-7528 Mainboard Specify Volume Size Start Creating RAID Volume from Existing Hard Drive WizardIntel ICH7R Sata RAID Start Migration Failed Hard Drive Member Degraded RAID ArrayMissing Hard Drive Member Intel ICH7R Sata RAID