MSI G31M3-F - Motherboard - Micro ATX Bios Setup Power Button Function, Restore On AC Power Loss

Page 50
Always leaves the computer in the power off state. Always leaves the computer in the power on state. Restores the system to the status before power failure or interrupt occurred.

BIOS Setup

Power Button Function

This feature sets the function of the power button. Settings are:

[On/ Off]

The power button functions as normal power off button.

[Suspend]

When you press the power button, the computer enters the

 

suspend/sleep mode, but if the button is pressed for more

 

than four seconds, the computer is turned off.

Restore On AC Power Loss

This item specifies whether your system will reboot after a power failure or interrupt occurs. Settings are:

[Off]

[On]

[Last State]

Wakeup Event Setup

Press <Enter> and the following sub-menu appears.

Resume From S3 By USB Device

The item allows the activity of the USB device to wake up the system from S3 (Suspend to RAM) sleep state.

Resume From S3 By PS/2 Keyboard

This setting determines whether the system will be awakened from what power saving modes when input signal of the PS/2 keyboard is detected.

Resume From S3 By PS/2 Mouse

This setting determines whether the system will be awakened from what power saving modes when input signal of the PS/2 mouse is detected.

Resume by PCI Device (PME#)

When set to [Enabled], the feature allows your system to be awakened from the power saving modes through any event on PME (Power Management Event).

Resume by PCI-E Device

When set to [Enabled], the feature allows your system to be awakened from the power saving modes through any event on PCIE device.

Resume by RTC Alarm

The field is used to enable or disable the feature of booting up the system on a scheduled time/date.

3-15

Image 50
Contents G31M3 series MS-7528 v1.X MainboardRevision History Copyright NoticeTrademarks Technical SupportSafety Instructions Micro-Star International MS-7528 FCC-B Radio Frequency Interference StatementWeee Waste Electrical and Electronic Equipment Statement Page Vii Contents Appendix B Intel ICH7R Sata RAID Getting Started Getting StartedSata Mainboard SpecificationsIDE Slots ConnectorsGetting Started Floppy Form FactorMainboard Layout G31M3 Series MS-7528 v1.X Micro-ATX MainboardPacking Checklist Hardware Setup Hardware SetupQuick Components Guide CPU Central Processing Unit Introduction to LGA 775 CPUCPU & Cooler Installation Lift the load lever up and open the load plate Locking switch DDR2 MemoryDual-Channel Memory Population Rules Installing Memory Modules Volt NotchATX 12V Power Connector JPW1 Power SupplyATX 24-Pin Power Connector ATX1 ATX1Back Panel LANAudio Ports Type a Audio Ports Type BIDE Connector IDE1 ConnectorsFloppy Disk Drive Connector FDD1 FDD1Supported by ICH7/ICH7Roptional Serial ATA Connector SATA1 ~ SATA4SATA4 SATA3 SATA2 SATA1 Fan Power Connectors CPUFAN1, SYSFAN1~2 Chassis Intrusion Connector JCI1JSPD1 IEEE1394 Connector J13941 optionalPDIF-Out Connector JSPD1 JFP2 JFP1 Front Panel Connectors JFP1, JFP2CD-In Connector CDIN1 CDIN1JAUD1 Front Panel Audio Connector JAUD1TPM Module connector JTPM1optional JTPM1JUSB1~2 Front USB Connector JUSB1 ~Serial Port Connector Jcom USB 2.0 BracketJBAT1 JumperClear Cmos Jumper JBAT1 PCI Peripheral Component Interconnect Slots SlotsPCI Peripheral Component Interconnect Express Slots PCI Interrupt Request Routing Bios Setup Bios SetupEntering Setup Press DEL to enter SetupGeneral Help F1 Control KeysGetting Help Main MenuMain Menu Exit Without Saving Bios Setup Load Optimized DefaultsSave & Exit Setup Standard Cmos Features DMA Mode Bios Setup Device / Vender / SizeLBA/Large Mode Hard Disk S.M.A.R.TMS-7528 Mainboard System Information Advanced Bios Features Hpet TCG/TPM Support Integrated Peripherals Device Configuration Bios Setup On-Chip Sata ControllerRAID Mode Parallel Port ModeAcpi Standby State Power Management SetupAcpi Function Wakeup Event Setup Bios Setup Power Button FunctionRestore On AC Power Loss Resume by RTC AlarmCPU Smart FAN Target MonitorChassis Intrusion Cell Menu Advance Dram Configuration tRAS Advance Dram Configuration tRCDAdvance Dram Configuration tRP Advance Dram Configuration tRTPAdjust Channel 0/1 Drive MS-7528 Mainboard Load Fail-Safe/ Optimized Defaults Bios Setting Password Dual Core Center Activating Dual Core Center Dual Core Center MainIntroduction Sharp mode Smooth mode Clock DOT Dynamic OverClocking Clock Voltage FAN Speed Temperature User Profile Dual Core Center Intel ICH7R Sata RAID ICH7R Introduction Creating, Deleting and Resetting RAID Volumes Bios ConfigurationUsing the Intel Matrix Stroage Manager Option ROM Intel ICH7R Sata RAIDCreate RAID Volume Intel ICH7R Sata RAID MS-7528 Mainboard Delete RAID Volume Reset Disks to Non-RAID † New Windows XP / 2000 Installation Installing SoftwareInstall Driver in Windows XP † Existing Windows XP/2000 Driver InstallationInstallation of Intel Matrix Storage Console Click on this itemIntel ICH7R Sata RAID MS-7528 Mainboard Intel ICH7R Sata RAID MS-7528 Mainboard RAID Migration Instructions Create RAID Volume from Existing Disk † RAID Level Intel ICH7R Sata RAID Configure Volume† RAID Volume Name † Strip Sizes Select the source diskIntel ICH7R Sata RAID Select Member Hard Drives MS-7528 Mainboard Specify Volume Size Start Creating RAID Volume from Existing Hard Drive WizardIntel ICH7R Sata RAID Start Migration Failed Hard Drive Member Degraded RAID ArrayMissing Hard Drive Member Intel ICH7R Sata RAID