MSI Z87-GD65-GAMING manual Profile

Page 86

Chapter 3

[By BIOS Options] OC Genie function is enabled by clicking the virtual OC Genie button at the top left corner of BIOS setup screen.

[By Onboard Button]OC Genie function is enabled by pressing the physical OC Genie button on the motherboard.

▶OC Genie Switch [Gear1]

Selects a kind of overclocking profiles for OC Genie Function. This item appears when "OC Genie Function Control" sets to [By BIOS Options].

[Gear1]

Enables Gear1 overclocking profile for overclocking.

[Gear2]

Enables Gear2 overclocking profile for extreme overclocking.

Important

We recommend that you do not to make any modification in OC menu and do not to load defaults after enabling the OC Genie function.

Updating BIOS or clearing CMOS is not allowed in OC Genie mode, and it may cause OC Genie function fail or other effect.

▶Adjust Ring Ratio [Auto]

Sets the ring ratio. The valid value range depends on the installed CPU.

▶Adjusted Ring Frequency

Shows the adjusted Ring frequency. Read-only.

▶Adjust GT Ratio [Auto]

Sets the integrated graphics ratio. The valid value range depends on the installed CPU.

▶Adjusted GT Frequency

Shows the adjusted integrated graphics frequency. Read-only.

▶DRAM Reference Clock [Auto]

Sets the DRAM reference clock. The valid value range depends on the installed CPU. This item appears when a CPU that supports this adjustment is installed.

▶DRAM Frequency [Auto]

Sets the DRAM frequency. Please note the overclocking behavior is not guaranteed.

▶Adjusted DRAM Frequency

Shows the adjusted DRAM frequency. Read-only.

▶Extreme Memory Profile (X.M.P) [Disabled]

X.M.P. (Extreme Memory Profile) is the overclocking technology by memory module. This item will be available when you install the memory modules that support X.M.P. technology.

[Disabled]

Disables this function.

[Profile 1]

Uses profile1 over-clocking settings of installed XMP memory module.

[Profile 2]

Uses profile2 over-clocking settings of installed XMP memory module.

DRAM Timing Mode [Auto] Selects the memory timing mode.

[Auto]

DRAM timings will be determined based on SPD (Serial Presence

 

Detect) of installed memory modules.

[Link]

Allows user to configure the DRAM timing manually for all memory

 

channel.

 

 

BIOS Setup

3-18

Image 86
Contents Preface G52-78451X1Preface Smartphone Application Technical Support Safety Instructions CE Conformity Korea Warning Statements Battery Information Weee Waste Electrical and Electronic Equipment Statement Español Türkçe Contents Quick Installation Appendix a Realtek Audio Page Chapter Packing Contents Optional AccessoriesAssembly Precautions Motherboard Specifications CPUBios Nvidia SLI Connectors Quick Guide Connectors Reference Guide Back Panel Quick Guide LED CPU Central Processing Unit Introduction to the LGA 1150 CPUCPU & Heatsink Installation Video DemonstrationChapter Chapter Dual -Channel mode Population Rule MemoryMounting Screw Holes Power Supply JPWR1~2 ATX Power ConnectorsExpansion Slots PCIE1~7 PCIe Expansion SlotSingle Video Card Installation Video/ Graphics CardsAMD CrossFire Multi -GPU Technology Chapter Nvidia SLI Technology Choose this item Internal Connectors SATA1~6 Sata ConnectorCPUFAN1~2,SYSFAN1~3 Fan Power Connectors JFP1, JFP2 System Panel Connectors JUSB1~3 USB 2.0 Expansion Connector JUSB4 USB 3.0 Expansion Connector JCI1 Chassis Intrusion ConnectorJTPM1 TPM Module Connector JCOM1 Serial Port ConnectorJAUD1 Front Panel Audio Connector MSATA1 mSATA SlotFV1 V-Check Connectors Voltage CheckpointsButtons OC1 OC Genie ButtonFASTB1 GO2BIOS Button POWER1 Power ButtonRESET1 Reset Button Jumpers JBAT1 Clear Cmos JumperSwitch Multi Bios Switch Multi -BIOS SwitchOCSWITCH1 OC Genie Mode Switch OC Switch LEDs LED Status IndicatorsBios LEDs Debug Code LED Table Total Installer Drivers and UtilitiesPage Quick Installation CPU Installation Quick Installation Memory Installation Motherboard Installation Chapter Power Connectors Installation Chapter Sata HDD Installation MSATA SSD Installation Front Panel Audio Connector Installation Front Panel Connector InstallationJFP1 Connecotr Installation USB3.0 Connector Installation Peripheral Connector InstallationUSB2.0 Connector Installation Graphics Card Installation Chapter Bios Setup Press DEL key to enter Setup Menu, F11 to enter Boot Menu Entering SetupEntering Bios Setup Overview Bar Operation Settings System StatusAdvanced Enables the Ipv6 PXE boot support IGD Partition size must be larger then the amount of memory Regulation Disabled Disables MSI Fast Boot Boot settings Boot SecuritySave & Exit This setting will be configured automatically by Bios LC PLL Profile UnLink Protection Over-current protection MEMORY-Z Can function as multiple systems virtually Then C0 Flash OC Profile Hardware Monitor Chapter Appendix a Software Configuration Software panel overviewAuto popup dialog Hardware Default Setting Backpanel audio jacks to 6-channel speakers diagram Page Appendix B Appendix B IntroductionUsing Intel Rapid Storage Technology Option ROM XXX.X GB Appendix B XXXX-XXXXXXXX Press Y key to accept the volume deletion XXXX-XXXXXXXX Recovery Volume Options Degraded RAID Array Main MenuAppendix B System Acceleration optional Appendix B RST Synchronization optional Disk Port