DEFY Front Loader WMY 81443 MLCM manual Connecting to the drain, Adjusting the feet

Page 6

1.Connect the special hoses supplied with the machine to the water inlets on the machine . Red hose (left) (max. 90 ºC) is for hot water inlet, blue hose (right) (max. 25 ºC) is for cold water inlet.

A warning: Ensure that the cold and hot water connections are made correctly when installing the machine to prevent laundry from coming out hot after the washing process resulting in undue wear.

2.Tighten all hose nuts by hand. Never use a tool when tightening the nuts.

3.Open the taps fully after completing the hose connection and check for water leaks. If there are any leaks, turn off the tap and remove the nut. Retighten the nut carefully after checking the seal. To prevent water leakages and damages caused by them, keep the taps closed when the machine is not in use.

2.5 Connecting to the drain

The end of the drain hose must be directly connected to the wastewater drain or to the washbasin.

A warning: Ensure that the end of the discharge hose is securely fixed into its housing to ensure the smooth flow of water and to avoid any risk of flooding and injury from hot water.

The hose must be attached to a height of at least 40 cm, and 100 cm at the most.

In case the hose is elevated after laying it on the floor level or close to the ground (less than 40 cm above the ground), water discharge becomes more difficult and the laundry may come out excessively wet. Therefore, follow the heights described in the figure. Ensure that the heights in the figure are followed.

100cm 40cm

The end of the hose must not be bent, it must not be stepped on and the hose must not be pinched between the drain and the machine.

If the length of the hose is too short, use it by adding an original extension hose. Length of the hose may not be longer than 3.2 m. To avoid water leak failures, the connection between the extension hose and the drain hose of the machine must be fitted well with an appropriate clamp as not to come off and leak.

2.6 Adjusting the feet

A warning: In order to ensure that the machine operates more silently and vibration-free, it must stand level and balanced on its feet. Balance the machine by adjusting the feet. Otherwise, the machine may move from its place and cause crushing and vibration problems.

1.Loosen the lock nuts on the feet by hand.

2.Adjust the feet until the machine stands level and balanced.

3.Tighten all lock nuts again by hand.

A warning: Do not use any tools to loosen the lock nuts. Otherwise, they will get damaged.

2.7 Electrical connection

Connect the machine to a grounded outlet protected by a 16 A fuse. The manufacturer and seller do not accept responsibility for any damage due to incorrect electrical connection.

Connection must comply with national regulations.

The Power cable plug must be within easy reach after installation.

If the current value of the fuse or breaker in the house is less than 16 Amps, have a qualified electrician install a 16 Amp fuse.

The voltage specified in the "Technical specifications" section must be equal to your mains voltage.

Do not make connections via extension cables or multi- plugs.

B warning: Damaged power cables must be replaced by an Authorized Service Agents.

To prevent flowing of dirty water back into the machine and to allow for easy discharge, do not immerse the hose end into the dirty water or do not drive it in the drain more than 15 cm. If it is too long, cut it short.

6 / EN

Washing Machine / User’s Manual

 

 

Image 6
Contents  Document Number 2820524090Dear Customer Explanation of symbols Important instructions for safety and environment Intended use Connecting water supply InstallationAppropriate installation location Removing packaging reinforcementConnecting to the drain Adjusting the feetElectrical connection Preparation Using detergent and softener Detergent DrawerCompartment nr Using limescale remover If the machine does not contain a liquid detergent cupDo not use bleaching agent and detergent by mixing them Display symbols Operating the machineControl panel Programs Programme selectionTemperature selection Spin speed selectionProgramme and consumption table Auxiliary function selection End TimeLoading door lock Switching the machine to pause modeStarting the programme Changing the selections after the programme has startedMaintenance and cleaning Draining remaining water and cleaning the pump filter Cleaning the body and control panelCleaning the water intake filters Close the taps0131 Install the filter0145 1000 rpmTechnical specifications Complying Commission Delegated Regulation EU No 1061/2010Rated capacity kg Troubleshooting Problem Reason Solution20 / EN 21 / EN 22 / EN Owner’s responsibility Service Centres Release the Company from its obligations WarrantyCompany Misuse