Panasonic WJ-ND400 manual User management, Basic user management settings

Page 196

User management

Configure the user and host authentication required to access the recorder from a PC. It is possible to restrict access by users and hosts (PCs).

Basics

Use the following procedure to specify whether user and host authentication should be performed.

1

2

Click the [User mng.] button on the setup menu.

On the sub-menu that appears, click [Basic].

This displays the basic user management settings window.

3

4

Configure the settings for each item.

Refer to “Basic user management settings” table for details about the settings.

Click the [Set] button.

Basic user management settings

Item

Settings

Description

 

 

 

User authentication

Off / On♦

Specifies whether user authentication should be performed.

 

 

 

Host authentication

Off♦ / On

Specifies whether host authentication should be performed.

 

 

• [On] cannot be selected for host authentication unless the

 

 

host is registered. First perform settings for the "Hosts

 

 

(page 71)".

 

 

 

♦Initial default

 

 

67

Page 195 Page 197
Image 196
Page 195 Page 197
Contents Network Disk Recorder Operating Instructions Model No. WJ-ND400Contents Contents AttachmentsContents TroubleshootingGlossary IndexPreface About these Operating InstructionsSystem Requirements for a PC Trademarks and Registered TrademarksRestrictions when operating MPEG-4 images Display and close the operating window About operating windowsStart the PC Launch the web browser Click the buttons and tabs to set up operations About operating windowsNames and functions of components TopControl button Multiscreen select box Sequence box El-zoom box Cam. select buttonCam. select box Setup button Status display area Playback point operation area HDD tabCamera at the time of recording CAM tab Recording mode and priority Priority Recording modeRecording images and audio Manual recording of images and audioPlayback Playback recorded imagesClick the HDD tab Click the Play button On the HDD tab, click the Stop buttonOperations during playback PlaybackFunction Button Operation Playback Search for and playback images Playback from a designated time and dateClick the Cam. select button Rec event list display Filter conditionsFilter Search Conditions Search for and playback recorded events Click the OK buttonClick the Rec event search button Conditions for filteringClick the VMD search button Click the Stop buttonSelect an area to play back Select the check box for the area to be played backLive images Screen displayUseful functions while images are displayed Live imagesFunction Name Button Operation Pan & tilt operations Camera controlClick the CAM tab Move a camera to the preset position Registration of a camera direction on the preset positionAuto mode function Auto pan etc Screen Multiscreen Display switching SequenceClick the Cam. select button Click the Sequence button Live images Event Event functionsAbout Events About event actionCanceling alarm action Suspend alarm actionDisplay the operation window Click the Alarm Suspend button Operations during an eventCancel the Error Status Preventing illegal operations CancelLock Error log Access logChecking logs Click the List buttonNetwork log Event logChecking logs Copying Copying recorded imagesClick the Control button Click the Copy button Playing back copied images Copying recorded imagesSelect the Copy area check box Click the OK button Click the HDD tab Click the log to playbackManual deletion Deleting imagesClick the Delete button Downloading images Downloading images for playbackClick the Download button Click the Save buttonInstalling the viewer software Downloaded image operationsDownloading images Downloading the viewer softwareUninstalling the viewer software Playing back imagesWindows XP Windows VistaSelect the downloaded image data file name.n3r Saving imagesClick the Open button Printing images Alteration detectionTransmit camera images when an event occurs Transmitting dataTransmitting to the FTP server Send mailChecking system/disk information System informationDisk information Click the Display button on the Disk information windowAbout mail notification Alarm mail notificationDescription About mail notification RAID6 3 DownAltered **CH Error log About the error logDescription of error Error log Network log ConnectorError log Output from ConnectorSkip COPY-HDD Full Area ERR COPY-HDD Full Ftploginfault Httpothererr Error operations About the error operationsError log display Description of error RemedyParameter in the logs above Error operationsParameter Description Detail Problems TroubleshootingProblem Check item/remedy Troubleshooting Audio is not be played correctly Troubleshooting Problem Remedy Message displayGlossary Words used in the manualGlossary Resolution Smtp authenticationSystem Administrator RouterIndex DNSPanasonic Canada Inc For European and other fields Panasonic Sales CompanyNetwork Disk Recorder Installation Guide For Your Safety Please Read the Following Text CARE- Fully This Class a digital apparatus complies with Canadian Ices Page Installation and Setup Description of FunctionsAbout Connectors Power SupplyUsing the Front Panel for Operations SpecificationsPreface Network Security Precautions Indication label Handle the unit with carePlace the unit horizontally on a level surface MPEG-4 Visual patent portfolio license GPL/LGPLMajor Operating Controls and Their Functions Front ViewMajor Operating Controls and Their Functions HDD access indicator A/F HDD status indicator STSInside the Front Cover USE button USEHDD bay slots RAID mode switch RAIDRemoval knob Using the Brace Rear ViewOutline of Functions Mega Pixel Camera Compatibility and CapacityHDD Space Management Replace HDDsOutline of Functions HDD Fault Tolerance SystemEncrypting Data Recorded on the HDDs Setting Schedules Recording and Playing ImagesStable recording and playback of images Event FunctionsSetup Menu List List of FunctionsEvent operations include the following Live MonitoringRemote Operation NetworkNetwork Security Function Maintenance Version Upgrade Recording Rate SettingSD Memory Recording Acquiring images stored on the SD memory cardSetup Procedure Getting StartedSetting up the Rack Install the recorder in the rackRack Mounting Remove the 5 rubber feet from the underside of the recorderSetting up the Rack Rack mounting positionsConnecting the PC and the Camera Using a HUB for Direct ConnectionConnections Port OperationConnections Connecting to a PC over Adsl Example of Connectivity with 1 Port OperationConnecting multiple units to the recorder HubhubExample of Connectivity with 2 Port Operation Connections Connecting the Extension Unit Secure connection cableAbout Connectors Using the Alarm/Control connectorPin Assignments Pin Name Description of Operation Remarks NumberAbout Connectors Connectivity for Switching to External RecordingAuto Adjustment Time Function Connection Connectivity for Emergency RecordingSignal ground Time adjustment input Connectivity for Control OutputUninterruptible Power Supply UPS Connectivity UPSUsing the Alarm Connector AlarmAlarm Connectivity Connectors Active Time Remarks Power Supply Turning On the PowerTurning Off the Power During RecordingUsing the Front Panel for Operations Basic OperationsUsing the Front Panel for Operations Checking System InformationCamera port Client PC port Maintenance port Checking the IP AddressSetting the IP Address Setting and Canceling Key LockConfiguring the Settings for Each Item Click the SET button when the cursor isHDD Unit Use the two screws to fasten the bottom of the HDDHandling the HDD ReferenceHDD is automatically recognized Installing HDDsPress the USE button for over 2 seconds Install the HDD units in the extension unit Installing HDDs by unitCheck the available disk space Removing HDDs Remove the HDD unit Check the disk informationRemoving HDDs by unit Hold down the USE button and turn on the power to boot up Setting the HDDs Operation ModeTurn off the recorder HDD Error Recovery During RAID Operation Data source During HDD error malfunction During recoveryReplacing Faulty HDD during RAID Operation Rebooting Troubleshooting Power cord gets warm or hot if bent Specifications General SpecificationsWJ-ND400 Input/outputAccessories Standard Accessories100BASE-TX 10BASE-T For business users in the European Union Network Disk Recorder Setup Instructions Initial configurations Disk management Encryption settings Alarm mail notificationData encryption Formatting disksPreface System Requirements for a PC Restrictions when operating MPEG-4 images Settings Recorder NetworkSetting item Description Setup menu listGetting started HDD Recorder network settings Network settingsSetting item Camera port Client PC port Maintenance port Use the arrow buttons to change the setting Network settingsAfter confirming that the cursor is , press the SET button PC network settings Double click Local Area ConnectionClick Properties Click Network ConnectionsClick Internet Protocol TCP/IP and then click Properties Click the OK button to close the windowAbout operating windows About operating windows Names and functions of components Search box Search button Area select button Copy box Next page buttonCam. select button Displays a menu for setting the server Alarm ALM button Error ERR button Pause button Next Image button Playback may start a few seconds CAM tab Click the setup menu button to configure Click the sub menu tab to configureQuick settings SettingsLanguage, and time & date settings Quick settingsNetwork setup Quick settingsUnder the Network setup item, click the Set button Camera registration Click the Registration buttonPort setup Camera port / Client PC port Program settings Basics Basic setupBasics Basics Time & dateTime display format Basics Emergency recording settings Click the Emergency rec. button on the setup menuEmergency recording Emergency recordingEmergency recording About SD memory recording About the Measurement buttonAcquiring images saved on the SD memory card Event Basic event settings Terminal alarm Terminal alarm settingsSite alarm Site alarm settingsCommand alarm Command alarm settingsSchedules ProgramProgram settings Schedules5ips 3ips10ips About the Measurement button Type of setting you want to configure Time table setupTime table About externally controlled recording Camera NW cameraAutomatically detecting and registering cameras PortNW camera settings CameraChecking and changing a camera Manually setting Switch cameras 4-screen display settingClick the Execute button Check or change the items you want Group Group settingsInput a group title Sequence Sequence display type settings Screen live sequenceNTP settings ServerFTP settings ServerServer Mail Mail settings SmtpProxy settings ProxyNetwork Network settings NetworkPort forwarding Ddns settings DdnsSnmp settings SnmpPanasonic alarm protocol Panasonic alarm protocol settingsBasic user management settings User managementAdministrator settings AdministratorUser management User setups UsersClick the User mng. button on the setup menu Editing user information Deleting user informationClick the Edit button Click the Registration button Click the Set buttonHost settings HostsEditing host information Deleting host informationUser level User level settings Maintenance Recorder informationRecorder information Check the items you wantMaintenance Click the recording information Display buttonDisk information Recording informationNetwork information Network informationDisk settings DiskDeleting image data from a disk Data deleteSettings management Settings managementConfiguring disks HDD space managementClick the Config. button on the setup menu Configuring disksDisk partition information Disk information Encryption settings Encryption settingsData encryption Information window, click EncryptionFormatting disks FormatInformation window, click Format Click the Format buttonFormatting disks Click the Main buttonOn the disk config top window, click Format Pre-event recording area formattingClick the Format button About mail notification Network Link Error RAID5 1 Down Altered **CH Troubleshooting Troubleshooting Troubleshooting Message display Glossary Glossary Smtp 100 101 Index3TR005560BAB A0408-1078 Solution ALL
Related manuals
Manual 60 pages 6.87 Kb

WJ-ND400 specifications

The Panasonic WJ-ND400 is a robust network video recorder (NVR) designed for reliable and scalable surveillance solutions. It serves as a central component in a modern security system, enabling the management and storage of video data from IP cameras. This device is particularly well-suited for a variety of applications, ranging from small retail setups to large enterprise installations.

One of the key features of the WJ-ND400 is its impressive storage capacity, supporting up to 16 terabytes of internal storage. This allows for extended recording times and the ability to retain high-resolution video footage without sacrificing quality. It supports various video compression formats, such as H.264 and H.265, which optimize file sizes and bandwidth use while maintaining clarity.

The WJ-ND400 boasts an intuitive user interface that facilitates seamless configuration and management of the recording settings. Users can access the device through a web browser, providing a convenient way to monitor live feeds, playback recorded footage, and manage camera settings from anywhere with an internet connection. This remote access feature is critical for businesses that require flexible surveillance management.

In terms of connectivity, the NVR supports Power over Ethernet (PoE), allowing for simplified installations by reducing the need for additional power supplies for IP cameras. The WJ-ND400 also utilizes a 10/100/1000 BASE-T Ethernet interface that ensures high-speed data transfer, optimizing the performance of connected devices.

Moreover, the WJ-ND400 is compatible with a wide range of Panasonic IP cameras, enhancing its versatility within a surveillance setup. It supports up to 64 channels of video input, enabling integration of multiple cameras for comprehensive coverage of surveillance areas.

Advanced features include motion detection and scheduled recording, allowing users to customize recording parameters based on specific needs. The NVR can also provide event alerts and notifications, enhancing its capability to respond to security incidents in real time.

In conclusion, the Panasonic WJ-ND400 stands out for its powerful storage capabilities, user-friendly interface, and extensive compatibility with various cameras. Its efficient use of high-quality video compression, combined with robust networking features, makes it an optimal choice for organizations looking to enhance their security infrastructure.
Top Page Image Contents