Set-Up, Hoses and Clamps | Multiquip QP305SLT, QPT305SLT instruction

SET-UP

Before Starting

1.Read safety instructions at the beginning of manual.

2.Place pump as near to water as possible, on a firm flat, level surface.

3.To prime pump, remove fill cap (See Figure 2) and fill pump casing with water. If the pump casing is not filled with water before starting, it will not begin pumping.

CAUTION

Pump casing must be filled with water before using pump. Otherwise, pump will not be able to begin pumping.

WARNING

DO NOT open fill cap if pump is hot!

Water inside may be under pressure.

4.Check for leaks between pump and engine. If water is leaking between the pump and engine housing, the seal inside the pump may be worn or damaged. Continued operation of the pump is not recommended. Further usage of the pump under these conditions may cause severe water damage to engine.

Hoses and Clamps

1.Check that all hoses are securely attached to the pump. Make certain suction hose (See Figure 2) does not have any air leakage. Tighten hose clamps and couplings as required.

2.It is recommended that 2 clamps be used when securing the suction hose to the inlet side (suction) of the pump.

3.Remember suction hoses must be rigid enough not to collapse when the pump is in operation.

4.Check that the discharge hose (See Figure 2) is not restricted. Place hose so that it lays as straight as it is possible on the ground. Remove any twists or sharp bends from hose which may block the flow of water.

NOTICE

Suction and discharge hoses are available from Multiquip. Contact your nearest dealer for more information.

5.The discharge hose is usually a collapsible (thin-walled) hose, however if a thin-walled discharge hose is not available, a rigid suction hose can be substituted in its place.

6.Make sure the suction strainer (See Figure 2) is clean and securely attached to the water end of the suction hose. The strainer is designed to protect the pump by preventing large objects from being pulled in to the pump.

CAUTION

The strainer should be positioned so it will remain completely under water. Running the pump with the strainer above water for long periods can damage the pump. To prevent the pump from drawing in sand and debris, place strainer on a board so that strainer will not touch bottom of water bed..

DANGER

DO NOT pump flammable fluids, corrosive chemicals or fluids containing toxic substances. These fluids can create potentially dangerous health and environmental hazards. Contact local authorities for assistance.

CAUTION

This pump uses a water-cooled mechanical seal to prevent water from seeping into the engine. The passage of water through the pump casing lubricates the seal and prevents it from overheating. NEVER! operate the pump without water in the casing as this will cause damage to the mechanical seal.

page 16 —QP305SLT/QPT305SLT CENTRIFUGAL PUMP • operation and parts manual — rev. #1 (10/11/10)

QPT305SLT, QP305SLT specifications

The Multiquip QPT305SLT is a state-of-the-art portable generator designed for construction sites, outdoor events, and emergency power needs. Known for its robust performance and reliability, the QPT305SLT is a standout choice for those requiring a dependable power source in demanding environments.

One of the main features of the QPT305SLT is its powerful engine. Equipped with a high-efficiency, 305 cc engine, the generator provides an output of up to 3,000 watts, making it suitable for various applications, from powering tools to providing backup energy during outages. The engine's design focuses on fuel efficiency and low emissions, aligning with current environmental standards while ensuring long operating times between refueling.

In terms of technology, the QPT305SLT incorporates advanced noise reduction systems, allowing it to operate at lower decibel levels, making it ideal for use in residential areas or noise-sensitive environments. An intelligent monitor system provides real-time data on voltage and frequency, ensuring that users are always aware of their power situation and can make informed decisions about their energy needs.

The QPT305SLT also features an integrated inverter, which helps deliver clean and stable power suitable for sensitive electronic devices. This feature is particularly beneficial for users needing to power computers, communication equipment, or medical devices. The inverter technology not only enhances the quality of the output power but also improves fuel efficiency.

Durability is another characteristic that sets the QPT305SLT apart. The generator is built with a heavy-duty frame and protective features to withstand the rigors of outdoor use. Additionally, it includes a maintenance-friendly design, making service checks and repairs straightforward.

Portability is a significant advantage of the QPT305SLT. With a lightweight construction and ergonomic handle design, moving the generator from one location to another is easy, making it an excellent choice for contractors and event organizers alike.

Overall, the Multiquip QPT305SLT combines power, efficiency, and user-friendly features, establishing itself as a reliable option for those in need of versatile and portable power solutions. Whether for job sites, outdoor activities, or emergency backups, this generator is engineered to meet the highest standards of performance and durability.