Maintenance pump, Pump Vacuum Test | Multiquip QPT305SLT, QP305SLT

maintenance (pump)

Pump Vacuum Test

CAUTION

DO NOT attempt to start the engine unless the pump has previously been primed with water. Severe pump damage will occur if pump has not been primed.

To perform the pump vacuum test do the following:

1.Remove the pump fill cap (See Figure 2), and fill the pump with water.

2.Start the engine as outlined in the initial start-up section, and wait for the pump to begin pumping.

3.As shown in Figure 17, place a water hose inside the discharge opening of the pump, and turn on the water. This flow of water into the discharge opening will prevent the pump from running dry.

4.Place the Pump Vacuum Tester (P/N 7000030) over the pump suction (inlet) opening (See Figure 17) with the vacuum gauge facing upwards. It may be necessary to apply a small amount of water around the rubber seal of the vacuum tester to make a good suction fit.

5.Check and make sure that there are no air leaks between the vacuum tester and the inlet port on the pump. If air leaks are present reseat vacuum tester.

6.Run the pump for a few minutes while monitoring the vacuum gauge. If the gauge indicates a reading between -25 and -20 in. Hg. (inches of mercury) then it can be assumed that the pump is working correctly.

NOTICE

25 in. Hg (inches of mercury) translates into 25 feet of lift at sea level.

7.If the vacuum tester gauge indicates a reading below -20 in. Hg, it can then be assumed that the pump is not functioning correctly, and corrective action needs to be taken.

8.To test the flapper valve, shutdown the engine. The vacuum tester should remain attached to the pump suction inlet port by vacuum.This indicates the pump's flapper valve is seating properly to hold water in the suction hose when the engine is stopped.This prevents backflow and allows for faster priming when the engine is restarted.

Adjusting Impeller Clearance

1.If it is necessary to replace impeller or volute, be sure clearance between impeller and volute is adjusted correctly.

2.The impeller should be as close to the volute as possible without rubbing against it. Clearance is adjusted by adding or removing shims from behind the impeller.

3.Check clearance between impeller and insert by slowly pulling starter rope to turn impeller. Remove spark plug to make it easier to turn impeller.

NOTICE

QP305SLT only — It is important not to remove too many shims or the clearance between the impeller and volute will become too wide and pump performance will be reduced. Remember as the impeller wear down, additional shims may be required to maintain the clearance between the impeller and insert.

4.Check the impeller every six months for wear, and for clearance between the impeller face and the volute. Also check the shaft seal for wear, as well as the shaft sleeve.

CAUTION

The impeller may develop sharp edges. Use extreme care when checking the impeller to prevent being cut.

QP305SLT/QPT305SLT CENTRIFUGAL PUMP • operation and parts manual — rev. #1 (10/11/10) — page 19

QPT305SLT, QP305SLT specifications

The Multiquip QPT305SLT is a state-of-the-art portable generator designed for construction sites, outdoor events, and emergency power needs. Known for its robust performance and reliability, the QPT305SLT is a standout choice for those requiring a dependable power source in demanding environments.

One of the main features of the QPT305SLT is its powerful engine. Equipped with a high-efficiency, 305 cc engine, the generator provides an output of up to 3,000 watts, making it suitable for various applications, from powering tools to providing backup energy during outages. The engine's design focuses on fuel efficiency and low emissions, aligning with current environmental standards while ensuring long operating times between refueling.

In terms of technology, the QPT305SLT incorporates advanced noise reduction systems, allowing it to operate at lower decibel levels, making it ideal for use in residential areas or noise-sensitive environments. An intelligent monitor system provides real-time data on voltage and frequency, ensuring that users are always aware of their power situation and can make informed decisions about their energy needs.

The QPT305SLT also features an integrated inverter, which helps deliver clean and stable power suitable for sensitive electronic devices. This feature is particularly beneficial for users needing to power computers, communication equipment, or medical devices. The inverter technology not only enhances the quality of the output power but also improves fuel efficiency.

Durability is another characteristic that sets the QPT305SLT apart. The generator is built with a heavy-duty frame and protective features to withstand the rigors of outdoor use. Additionally, it includes a maintenance-friendly design, making service checks and repairs straightforward.

Portability is a significant advantage of the QPT305SLT. With a lightweight construction and ergonomic handle design, moving the generator from one location to another is easy, making it an excellent choice for contractors and event organizers alike.

Overall, the Multiquip QPT305SLT combines power, efficiency, and user-friendly features, establishing itself as a reliable option for those in need of versatile and portable power solutions. Whether for job sites, outdoor activities, or emergency backups, this generator is engineered to meet the highest standards of performance and durability.