GE RINTERxxxPS(P) Relay Panel Installation, Install Interior, Power Supply, Wire Line Voltage

DEH40212 Installation Instructions

CAUTION: Make sure all power is OFF before wiring.

Do not energize wiring until the unit is fully assembled.

Conform to all applicable codes.

RELAY PANEL INSTALLATION

Figure 1

Dimensions (A x B)

RINTER1212PS(P)

SWITCHED LIGHTING CIRCUITS

1.5" x 1.5" CROSSOVER WIRING CHANNEL (TOP AND BOTTOM) 2" TYP.

16.0" (406mm) x 16.5" (419mm)

RINTER2424PS(P)

22.5" (572mm) x 24.0" (610mm)

RINTER4848PS(P)

36.0" (914mm) x 24.0" (610mm)

Relay Capacities (C)

RINTER1212PS	12 RR7 relays
RINTER1212PSP	12 RR9 relays
RINTER2424PS	24 RR7 relays
RINTER2424PSP	24 RR9 relays
RINTER4848PS	48 RR7 relays
RINTER4848PSP	48 RR9 relays

DIN Rail Capacities

A

RELAYS	CLASS 2	RELAYS
	LOW-VOLTAGE
	WIRING SECTION
C		C
	DIN RAIL

CIRCUIT BREAKER PANEL

RINTER1212PS(P)	One module	4.5" D	LINE-VOLTAGE WIRING SECTIONS
RINTER2424PS(P)	Two modules			5" WIDE
					B			ILLUSTRATION NOT TO SCALE
RINTER4848PS(P)	Two modules
If you have purchased the ProSys II Lighting Control System						Install Interior
(the stand-alone system), the devices (panels, switches and						• Power Supply
clock) will be in self-install mode, which means that as soon							Attach the power supply to the frame (bottom of 12-relay
as they are connected to the network, they are operational							interior and left side of 24- or 48-relay interiors) and plug
and can communicate with each other.							the low-voltage connector to the terminal marked “POWER”
If you have purchased the ProSys LM Lighting Control System							as shown in Figure 1 above.
						• Interior
along with the ProSys LM software, the devices will be in
							Mount the interior in the tub and secure it to the studs with
software-install mode. This means that in order for them to
							the hardware provided. Make sure that all line- and low-
function on the network you must:
							voltage wiring is confined to the appropriate areas.
• assign network addresses to the devices and
• bind network variables and message tags using your						Wire Line Voltage
network management tool.						Before making any connections to the relays, make sure that
Addresses and binding are necessary for the devices to function on						none of the load circuits are shorted. Wire from the circuit
						breaker through each relay’s SPST output terminals, and from
the network. ProSys LM users please refer to the ProSys LM
						there to the loads. Confirm that each circuit is wired to the
Software User Guide for instructions on installing devices.
						relay specified in the drawings. Wire the power supply.

Rough-In Tub

•Environment

32 to 131oF (0 to 50 oC), 0 to 95% relative humidity, stationary applications

•Mounting

The tub should be level, plumb and rigidly installed with hardware sufficient to hold 100 lbs. (48kg). For flush-mount panels, the front flange should be flush with the final finished surface. For multiple panels, allow 1⁄4” minimum between panels for showbox cover clearance.

•Pulling Wires

Route line-voltage wiring through the 2 1⁄2” knockouts in either the top or bottom of the tub. Route Class 2 low- voltage dataline from the remote switches or other controls through the 3⁄4” knockouts in either end.

Figure 2
115	NEU GRD	J2
VAC
	GE Lighting Controls
		RINTER2424PS
		shown

2