GE ASQ18, ASM14*, ASM24* installation instructions Consumer, Support

Page 5

ge.com

Additional controls and important information.

Do Not Operate in Freezing Outdoor Conditions

This cool-only air conditioner was not designed for freezing outdoor conditions. It must not be used in freezing outdoor conditions.

When the air conditioner is turned on, it will automatically start in the setting last used.

Power Outage Recovery Feature

In the case of a power outage or interruption, the

Sleep features will reset to the original setting.

unit will automatically re-start in the settings last

You may need to set a new time if desired.

used after the power is restored. The Timer and

 

 

 

Safety Instructions Operating

Cool Mode

Use the Cool mode with High (3), Med (2) or Low (1) fan for cooling. Use the Increase / Decrease pads to set the desired temperature between 64°F and 86°F in 1°F increments.

A thermostat is used to maintain the room temperature. The compressor will cycle on and off to keep the room at the set level of comfort. Set the thermostat at a lower number and the indoor air will become cooler. Set the thermostat at a higher number and the indoor air will become warmer.

NOTE: If the air conditioner is off and is then turned on while set to Cool, it will take approximately 3 minutes for the compressor to start and cooling to begin.

Cooling Descriptions

For Normal Cooling—Select the Cool mode and High (3) or Med (2) fan with a middle set temperature.

For Maximum Cooling—Select the Cool mode and High (3) fan with a lower set temperature.

For Quieter & Nighttime Cooling—Select the Cool mode and Low (1) fan with a middle set

temperature.

NOTE: If you switch from a Cool setting to Off or to

a fan setting, wait at least 3 minutes before switching back to a Cool setting.

Instructions Installation Instructions

Fan Mode

Use the Fan at High (3), Med (2) or Low (1) to provide

Since fan only settings do not provide cooling,

air circulation and filtering without cooling.

a temperature setting will not be displayed.

Vent Control (on some models)

The vent control is located on the inside of the air louvers in the lower right corner.

When set at CLOSE, only the air inside the room will be circulated and conditioned. When set at OPEN, some inside air is exhausted outside.

 

OR

To open the vent, push the lever to the

To open the vent, push the

right. To close it, push it to the left.

lever to the right. To close

 

it, push it to the left.

Troubleshooting Tips

Air Direction—Up and Down (on some models)

Fingertip pressure on the horizontal louvers adjusts

OR

the air direction up or down.

 

Air Direction—Side-to-Side (on some models)

On some models, the side-to-side air direction is

Consumer

adjusted by the louver levers or by grasping and moving the inner vertical louvers.

OR

5

Support

Image 5
Contents Write the model and serial numbers here Model # Serial # Air ConditionersDo not use an adapter plug with this appliance Consumer Support Troubleshooting TipsGe.com USE of Extension CORDS-115-Volt models onlyRemote Control Instructions Safety InstructionsSupport ConsumerConsumer Support Air Direction-Side-to-Side Safety InstructionsConsumer Support Troubleshooting Care and cleaning of the air conditionerHow to Insert the Batteries Air FilterTools YOU will Need Before YOU BeginElectrical Requirements Parts Included Window Installation InstructionsRemove the Front Grille if Attached Window RequirementsStorm Window Requirements Prepare the Case Remove the AIR Conditioner from the CaseInstall the Case in the Window Install the CaseInstall the Security Bracket and the Foam TOP Window Gasket Install the AIR Conditioner in the Case Finish the Wall Opening Through-the-Wall Installation Instructions-OptionalNormal Operating Sounds Troubleshooting Tips…We’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration Installation Instructions GE Air Conditioner WarrantyWhat Is Not Covered GE Will ReplaceParts and Accessories Schedule ServiceConsumer Support GE Appliances Website Real Life Design StudioAcondicionadores de Aire Instrucciones de Operación Instalación Instrucciones de SeguridadInstrucciones Solución de problemas Apoyo al consumidor instalaciónSeguridad Instalación Consumidor Solucionar problemasApoyo al Control remotoModo Cool Frio Función de recuperación de pérdida de energíaModo de FAN Ventilador Control de la ventilación en algunos modelosConsumidor Instrucciones de SeguridadControl de la ventilación en algunos modelos Dirección del aire-de lado a ladoPrecaución no Opere el Cuidado y limpieza del acondicionador de aireApoyo al consumidor Solución Cómo insertar las bateríasRequisitos Electricos Antes DE IniciarPartes Incluidas Herramientas QUE Usted NecesitaráRetire LA Parrilla Frontal SI Está Pegada Requisitos Para LA VentanaRequisitos DE UNA Ventana DE Tormentas Retire EL Acondicionador DE Aire DE LA Caja Prepare LA CajaInstale LA Caja EN LA Ventana Instale LA CajaDE LA Ventana Instale EL Acondicionador DE Aire EN LA Caja Importante Instrucciones de instalación a través de la pared-opcionalExterior Termine LA Abertura EN LA ParedSolucionar problemas Sonidos de operación normales Instrucciones de Seguridad Operación InstalaciónGE reemplazará Garantía de su acondicionador de aire de GELo que no está cubierto Un añoSolicite una reparación Apoyo al Consumidor Página Web de GE AppliancesGarantías ampliadas Piezas y accesorios

ASQ18, ASM24*, ASM14* specifications

GE ASM14*, ASQ18, ASM24* are part of General Electric's advanced suite of air compressor technologies designed for energy efficiency and reliability. These models cater to various industrial applications that require compressed air solutions, offering distinct features that enhance operational performance.

The ASM14* model is engineered with advanced airend technology, which ensures increased efficiency and reduced power consumption. This results in lower operational costs while providing consistent airflow. It employs a robust design that minimizes maintenance needs, making it a preferred choice for industries looking for reliable performance without frequent downtime.

ASQ18 offers high adaptability to different environmental conditions. This model features integrated variable speed drive (VSD) technology, which adjusts the compressor output based on the actual air demand. This not only optimizes energy consumption but also reduces wear and tear, extending the lifecycle of the unit. ASQ18 is perfect for facilities that experience fluctuating air requirements and emphasizes sustainability through reduced energy usage.

Similarly, the ASM24* model brings impressive capabilities to the table, particularly in terms of airflow and pressure characteristics. Its compact design allows easy integration into existing setups, and it boasts a low noise level, making it suitable for various applications where noise reduction is critical. This model incorporates easy-to-access components that simplify maintenance, ensuring operational continuity.

All three models utilize advanced monitoring technologies, providing real-time data on performance and operational health. This enables users to make informed decisions regarding maintenance schedules, ultimately enhancing productivity. Additionally, GE’s commitment to incorporating smart technologies ensures compatibility with predictive maintenance systems, allowing for proactive issue resolution.

In summary, the GE ASM14*, ASQ18, and ASM24* compressors stand out for their commitment to efficiency, sustainability, and reliability. With their advanced engineering, they cater to diverse industrial needs while helping businesses minimize operational costs and enhance productivity. Choosing these models means capitalizing on GE's legacy of quality and innovation in the compressed air sector.