Using the FM/AM radio, If noise is excessive

Using the FM/AM radio

	∫ If noise is excessive
	When “FM” is selected
TUNER/BAND	Press and hold [—FM MODE] on
	the main unit to display
	“MONO”.

Numbered buttons

, ,

ENTER

FUNCTIONS

CM SKIP

Press and hold [—FM MODE] again to cancel the mode.

≥The mode is also canceled when you change the frequency.

	When “AM” is selected
	Press [FUNCTIONS] on the remote control.
	Each time you press the button: BP 2()BP 1

	Manual tuning

1	Press [TUNER/BAND]§1 to select “FM” or “AM”.
2	Press [6, 5]§2 to select the frequency.
	≥When performing this step on the main unit, first press

[-TUNE MODE] to select “MANUAL”, and then press [X TUNING W] to select the frequency.

≥To start automatic tuning, press and hold [6, 5] until the frequency starts scrolling. Tuning stops when a station is found.

radio

SELECTOR MEMORY

∫ Presetting the channel

Using the FM/AM

TUNING $\Main\unit\only]$

-TUNE MODE / -FM MODE

Radio operations are described mainly with the remote control.

You can alternatively use the corresponding button on the main unit.

§1 [SELECTOR]

§2 [X TUNING W]

§3 [MEMORY]

Presetting stations automatically

Up to 30 stations can be set in each band, FM and AM.

1	Press [TUNER/BAND]§1 to select “FM” or “AM”.
2	Press and hold [ENTER]§3.
	Release the button when “FM AUTO” or “AM AUTO” is displayed.

The tuner tunes to the lowest frequency and starts to preset all the stations it can receive into the channels in ascending order.

≥“SET OK” is displayed when the stations are set, and the radio tunes to the last preset station.

≥“ERROR” is displayed when automatic presetting is unsuccessful. Preset the channels manually (➜ right).

Up to 30 stations can be set in each band, FM and AM.

1While listening to the radio broadcast

Press [ENTER]§3.

2While the frequency and “PGM” are flashing on the display

Press the numbered buttons to select a channel.

≥To select a 2-digit number

DISC S.SRD TG KARA D.MIX MONO SLP

e.g. 12:

[S10] ➜ [1] ➜ [2]

Alternatively, press [X, W], and then press [ENTER]§3.

A station previously stored is overwritten when another station is stored in the same channel preset.

FM frequency step\Main\unit\only]

The step is factory-set to 0.2-MHz, but you can change it to receive broadcasts allocated in 0.1-MHz steps.

1Press [SELECTOR] to select “FM”.

2Press and hold [SELECTOR].

After a few seconds the display changes to show the current minimum frequency. Continue to hold the button down. The minimum frequency changes and the step is changed.

To return to the original step, repeat steps 1 and 2.

[Note]

After changing the setting, previously preset frequencies will be cleared.

Preset them again.

Selecting the preset channels

1	Press [TUNER/BAND]§1 to select “FM” or “AM”.
2	Press the numbered buttons to select the channel.
	≥To select a 2-digit number
		SB DISC S.SRD TG KARA D.MIX MONO SLP
	e.g. 12: [S10] ➜ [1] ➜ [2]
		DVD
	Alternatively, press [X, W].	CD
		ODE

RQTX0014

≥To perform this step on the main

unit, first press [-TUNE MODE] to select “PRESET”, and then press [X TUNING W] to select the channel.

When a stereo FM broadcast is being received, “ST” lights in the display.