SkyLink manual Model GT-100, Wall Console, Garage Door MonitorTM Sensor

Garage Door CloserTM	Model GT-100
1. INTRODUCTION

2. INSTALLATION (CONT)

Congratulations on your purchase of the Skylink® Garage Door Closer Model GT-100. Skylink® Garage Door Closer is very easy to install, and provides you with the peace of mind you have been looking for by knowing your garage door will not be left open anymore. Skylink® Garage Door Closer consists of 2 units:

Garage Door

MonitorTM Sensor

(Battery Included)	Double-sided
GS-101	foam tape
3V Lithium battery
4 pcs 3 x 18 screws		Wall Console
2 pcs 3.5 x 25 screws	Extension wires	GT-100R

Wall Console does not require any battery to operate and it can replace most of the existing garage door opener’s push buttons. Garage Door

Step 2 – Mount the sensor on to your garage door

You can mount the sensor onto your garage door with double-sided foam tape if the sur- face of your garage door is smooth and clean enough to provide a good adhesive surface, such surface can usually be found on a me tal garage door. Please ensure the surface is smooth and clean. Important: The bottom of the sensor should be 1/2 inch above the ground. (Refer to Diagram A)

For w ooden garage doors, it is recommended	4 Screws
to mount the sensor with screws on to the
garage door with 3 x 18 screws provided.

Double-sided foam tape

Sensor is battery operated and can be mounted on to the garage door by double sided tape or screws. These 2 units operate wirelessly which simplifies the installation.

Programming is very simple, you can select the time you would like the door to be closed after it has been opened. The selectable door closing times are 2 minutes, 5 minutes, 10 minutes and 20 minutes.

WARNING

Before installing the Skylink® garage door closer, ensure your garage door is equipped with an external entrapment protection device, such as an infrared beam sensor which “sees” an object obstructing the door without having actual contact with the object. A Garage door opener does that not have the auto reversing mechanism should be replaced by one that has the auto reversing mechanism feature and the garage door closer must not be installed on garage a door opener without this feature.

Without a properly working safety reversal system, a person could be seriously injured or killed by a closing garage door.

2. INSTALLATION

	Unplug the power cord of your garage door opener
WARNING	before installation to ensure power is not connected.

Note:

When the garage door is opening/closing, make sure the sensor does not interfere with the safety reversing sensor or safety beam sensor supplied with your existing garage door opener.

Note: Ensure you straighten up the antenna	1/2 Inch
on the receiver to receive the best possible		Diagram A
reception.

Wall Console

The GT-100R Wall Console replaces most garage door “push buttons” or “wall consoles”. There are 2 different kinds of “push buttons”.

1) Single button

2) Multi-Function Wall Console

1) Single button

The installation involves 2 units:

1)Garage Door MonitorTM Sensor

2)Wall Console

Garage Door MonitorTM Sensor

Step 1 – Select a spot on your garage door to mount the sensor

Before you install the sensor onto the garage door, make sure the garage door is closed. The sensor assembly should be mounted on one of the vertical supports of your garage door near the bottom.

Remove the battery isolator

If your garage door opener equips with a single button “push button”, you can replace the existing push button with Skylink® Garage Door Closer Wall Console GT-100R. Please follow the procedures below.

1. Remove the existing push button by removing the screws.

2. Disconnect the 2 wires that are connected to

the existing push button.	Remove
	existing
	wires

3. Connect these 2 wires to the 2 terminals on the GT-100R Wall Console. Loosen the 2 screws on the terminals, feed the 2 wires to the 2 terminals and tighten 2 screws to secure the

When the door is closed, the detection rod should be retracted. When the door is open, the detection rod will be extended.

One of

Vertical

Supports

Door closed Door open

2 wires.

4.After connecting the 2 wires, the red LED under- neath the push button will be on. The GT-100R is now charging up. The GT-100R will be fully charged when the buzzer emits a beep (approx

10 seconds to 1 minute depending on the brand of garage door opener), the red LED will then flash slowly. The GT-100R is now ready to operate.

5. Mount the Wall Console to the wall with 2 screws.

6. Straighten up the antenna on the GT-100R.