SkyLink GT-100 manual Operation, Accessories

3. OPERATION (CONT)

Operation

	Antenna
	Push button
Loss of Signal LED	Timer / Learn LED
Lock button	Learn button

Push Button

Press the push button to open or close the garage door.

Lock Button

Lock feature is designed to prevent Skylink® handheld remotes such as Skylink® Keychain Remote Model 4B-201 (sold separately) to operate the garage door opener.

To activate the lock feature

1.Press and hold the lock button for approx. 2 seconds, then release it.

2.When the lock feature is activated, the red LED underneath the push button will flash rapidly.

Note: If a valid wireless remote signal is received while the lock feature is activated, wall console will beep to reminding you the wall console is locked.

To deactivate the lock feature

1.Press and hold the lock button for approx. 2 seconds, then release it.

2.When the lock feature is deactivated, the red LED underneath the push button will flash slowly indicating the wall console is in normal operating mode and the lock feature is deactivated.

Learn Button

Skylink® Wall Console can be used as a garage door opener receiver. It does not only operate as a garage door closer, additional handheld remote controls can be added. Additional remote controls are sold separately.

To program Skylink’s remote control / sensor

1.Press the learn button for approx. 5 seconds.

2.The “Timer / Learn” red LED will be on, release the learn button.

3.Activate the Skylink® remote control. If the Skylink® remote control has multiple buttons, press the button you would like to operate.

4.The “Timer / Learn” LED will be off after it has successfully programmed the remote control.

5.You can now press the programmed remote to operate the garage door opener.

Erase Skylink® remote controls / sensors

To erase unwanted remote control(s), first erase all remote controls and sensors, then program the ones you would like to keep.

Erase all remote controls / sensors

1.Press and hold the learn button for 15 seconds.

2.The “Timer / Learn” red LED will flash rapidly meaning all remote have been erased.

3.You have now successfully erased all the remote controls and sensors. Follow the instructions “To program Skylink’s remote control” to add the remote control(s) you would like to keep.

3. OPERATION (CONT)

Chamberlain®, Lift-Master®, Sears Craftsman® Multi-Function Wall Console

There are 3 buttons on the Multi-Function Wall Console:

1)Push Button - Open / Close garage door.

2)Lock Button - Enable / Disable handheld remotes to operate the garage door opener.

3)Light Button - Turn on / off light.

Skylink® Wall Console also has 3 buttons, their functions are identical to the Chamberlain® / Lift-Master® / Sears Craftsman® wall console.

Chamberlain®/ Lift-Master®/	Function	Equivalent button on
Sears®		Skylink ® wall console
Push Bar	Open / Close door	Push Button
Lock Button	Enable / Disable operation	Lock Button
	from handheld remotes
Light Button	Turn light on / off	Learn Button
Chamberlain®
	Open / Close door
Prevents operation
from handheld remotes			Turn light on / off

Loss of Signal

Skylink® Wall Console also monitors the status of the garage door sensor. If the garage door sensor fails to communicate w ith the wall console, the loss of signal LED will flash indicating a trouble condition for the sensor. There are 2 types of sensors. The flashing is different depending on the type of sensor:

Garage Door Sensor: One flash at a time

Audio Sensor (Optional Accessory): Two flashes at a time

When the loss of signal is flashing, please check the following:

-Check the battery of the sensor.

-The LED on the sensor should flash when the sensor is triggered.

For the detail of how the Audio Sensor works, please refer to “Accessories”.

4. ACCESSORIES

Optional accessories can be added to the garage door closer.

4-Button Keychain Remote – Model 4B-201

- Keychain remote can be programmed to the garage door closer so it operates the garage door opener like an ordinary remote control.

- It transmits Skylink® rolling code.

-Multiple buttons allow operation of multiple garage door openers and lighting / appliances control.

Audio Sensor – Model AS-101

-The Audio Sensor is to be used in conjunction with the Skylink® garage door closer and any CO detector

(sold separately). It is used to detect the CO emission inside the garage.

-When the CO level exceeds the safety limit, the alarm from the CO detector will sound, which will trigger

Skylink’s Audio Sensor. Skylink® wall console will open the garage door for 10 minutes to improve air circulation. Door will then be closed automatically after the CO level resumes within the safety limit.