Programming WINDOW/DOOR Sensor, Test Sensor

Page 2 of 3

4. PROGRAMMING WINDOW/DOOR SENSOR

The sensor must be programmed to the Household Alert® Long Range Receiver before they can communication. You may program the sensor to one of the 4 zones. Follow the instructions below;

1.Plug in an AC adapter to the receiver.

2.Power up the Receiver unit. The green LED will be on indicating it is turn on.

3.Open the back cover and there is a learn button. Press and hold this learn button for 5 seconds, until both green LED and zone 1

red LED You may now release the learn button.

4.If you would like to program the sensor to zone 1, activate the

sensor while the zone 1 red LED is Activate the Sensor by separating the magnetic contact from the sensor.

5.If you would like to program the sensor to other zones, press the

learn button again, until the red LED at the zone you want to program the sensor to, then activate the sensor.

6.Once the sensor is programmed, the green LED will be steadily on and none of the red zone LEDs will be on.

Plug in the adapter to the receiver

Separate the magnet from the sensor, Receiver zone LED

stops.

Learn Button

Note: Each zone can program up to 4 sensors. If you try to program a

sensor into a zone, the programmed sensor will be erased.

Test Sensor

After learning the sensor to the Receiver unit, you may test the com- munication by placing the magnet beside the sensor (where the red marking is) and remove the magnet from the sensor.

When the magnetic is closed, the	When the magnetic contact is broken (open),
receiver will not beep.	the receiver will beep and zone LED will	.

1)Zone LED of this sensor will h.

2)Beeping according to the zone number [Operating mode is set to “Alert”]. 1 beep for zone 1, 2 beeps for zone 2 and etc, until the magnetic contact is closed.

Erasing a sensor

You cannot erase a sensor. You must erase all sensors from the receiver, then program the ones you would like to keep. To erase all the sensors from the receiver:

1.Remove the adapter from the receiver.

2.Open the back cover, press and hold the learn button. Do not release the learn button until step 4.

3.While holding onto the learn button, plug in the adapter to the receiver.

4.You may release the learn button when the LEDs on the receiver are on.

5.You have erased all sensors from the receiver.

5. WINDOW/DOOR SENSOR INSTALLATION

The transmitters should be mounted on the door frame or window frame by double sided tape. The magnet should be mounted on the door or window by either double sided tape or screws. Make sure the magnet is aligned with the red marking on the transmitter. If the surface of the frame

is enough, double-sided foam tape is otherwise, it is recommended to screw the mounting plate to the frame, then apply double sided tape. After mounting the sensor, if the Skylink logo is inverted, remove the front cover and rotate it so the Skylink logo is in the upright position.

	Magnet	"Red Marking"	Magnet
"Red Marking"		on the side
on the side	Sensor	Sensor

Mounting plate	Double-sided	Sensor
and screws (optional)	foam tape

6. OPERATION

There are 3 di operating modes for the Household Alert® Long Range Receiver.

1)Alert - Beeps when a sensor is activated, corresponding zone LED

will also .

2)Alarm - Sounds an alarm when a sensor is activated, corresponding

zone LED will also .

3) - No audio sound will be emitted when sensor is activated.

Zone LED will to indicate the activated sensor.

To select the operating mode, place the

slide switch on the side at the desired setting:

OFF - No Audio

ALERT - Alert Mode

ALARM - Alarm Mode

Operation

Alert

When motion is detected in the monitored area, the sensor will send a signal to the receiver. It will beep and the corresponding zone red LED

will for 15 seconds.

If the sensor is set to zone 1, zone 1 red LED on the receiver will and the receiver will emit a continuous “single beep”, i.e. “beep” pause, “beep”, pause….. etc.

If the sensor is set to zone 4, zone 4 red LED will and the receiver will emit a continuous “4 beeps”, i.e. “beep beep beep beep” pause “beep beep beep beep” pause ……etc.

By the number of beeps emitted by the receiver, user can identify which zone is triggered.

HA-400 specifications

The SkyLink HA-400 is an innovative and technologically advanced UAV designed to cater to various aerial needs, including surveillance, mapping, and delivery services. Its robust construction, combined with cutting-edge features, enables it to perform effectively across diverse environments and scenarios.

One of the standout features of the SkyLink HA-400 is its impressive flight time. With a maximum endurance of up to 45 minutes, users can expect extended operational periods, allowing for comprehensive data collection or monitoring missions without frequent recharges. The UAV is equipped with a high-capacity battery that not only enhances flight time but also supports quick recharging, ensuring minimal downtime.

The HA-400 boasts a state-of-the-art flight management system that incorporates GPS and advanced autopilot capabilities. This technology allows for precise navigation and positioning, significantly improving mission planning and execution. Users can set waypoints and define automated flight paths, making it ideal for repetitive tasks such as agricultural monitoring or infrastructure inspections.

For imaging and surveillance, the SkyLink HA-400 is outfitted with a high-resolution camera system. This includes both optical and thermal imaging options, enabling the UAV to capture detailed visuals in various conditions, including low light and adverse weather. The camera's pan-tilt-zoom functionality allows operators to adjust the view remotely, ensuring they can focus on points of interest during a flight.

The HA-400 is designed with durability in mind. Its lightweight but sturdy materials ensure it can withstand the rigors of outdoor use while maintaining a stable flight profile. Additionally, the UAV features advanced obstacle avoidance technology, allowing it to navigate complex environments safely.

With an intuitive user interface and mobile app compatibility, controlling the SkyLink HA-400 is user-friendly. Operators can monitor telemetry data in real-time and adjust flight parameters with ease. Furthermore, the UAV supports live HD video streaming, enabling immediate tactical decisions based on current visuals.

The versatility and technological robustness of the SkyLink HA-400 make it a top choice for professionals across various industries, from agriculture and construction to security and environmental monitoring, providing unmatched performance tailored to the needs of modern aerial operations.