American Standard 065.525, 6065.161, 6065.565 Install Flush Valve a & 8b, Adjust Supply Stop Fig

Page 6

6INSTALL FLUSH VALVE; Fig. 8a & 8b

1.As shown in Fig. 8a, insert the side INLET FLANGE (1) on the FLUSH VALVE (2) into the SUPPLY STOP (3). Lubricate the INLET FLANGE O-RING (4) with water if necessary. Lightly tighten COUPLING NUT (5). Fig. 8a.

Important: Do not use lubricants (other than water) or any type of thread sealing paste or tape.

2.Align the FLUSH VALVE (2) (Fig. 8b) directly above the DOWN TUBE (7) and VACUUM BREAKER COUPLING NUT (6). Make sure that GASKET (10) is installed.

Note: There is a +13mm, -6mm (+1/2, -1/4) tolerance for the 121mm (4-3/4) dimension. Fig. 8b.

3.Pull the DOWN TUBE (7) up to meet the threaded FLUSH VALVE CONNECTION (8) and hand tighten the VACUUM BREAKER COUPLING NUT (6). Align all components of the flush valve assembly. Fig. 8b.

4.Lightly tighten the COUPLING NUT (5) connection first, then the VACUUM BREAKER COUPLING NUT

(6) and finally the SPUD COUPLING NUT (9). Once alligned correctly, use a wrench to tighten couplings to make water tight connections. Fig. 8b.

7ADJUST SUPPLY STOP; Fig. 9

IMPORTANT: To avoid overflowing, the SUPPLY STOP

(3)must never be opened to the point where the flow from the valve exceeds the flow capacity of the fixture. The fixture must be able to handle a continuous flow in case of a flush valve failure.

1.After installation is complete, peel off the PROTECTIVE FILM (1) from the sensor. Standing to one side, block the sensor with your hand for 10 seconds.

Remove your hand and listen for audible “click” from within the valve.

2.Remove COVER (2) from SUPPLY STOP (3).Turn on water supply 1/4 turn to 1/2 turn(CCW) and test for leaks. Note: Unit may flush for approximately 5 to 10 sec. when water is first turned on. If flow persists, turn water off and repeat step #1 above.

3.Actuate the FLUSH VALVE:

A)Cover sensor with hand for 10 seconds.

NOTE: Stand outside of sensor detection aera.

B)Remove hand from in front of the sensor; unit will flush in approximately 3 seconds.

4.Adjust SUPPLY STOP (3) after each flush until the stated flush volume is achieved, no splashing occurs and the fixture is properly cleansed.

5.When adjustment is complete, replace COVER (2) and tighten to ensure vandal-resistance.

Fig. 8a

 

 

 

 

3

 

 

1

 

5

4

 

2

 

Fig. 8b

121mm,+13mm, -6mm

(4-3/4)(+1/2, -1/4)

 

5 2 8 10

6

7

9

Fig. 9

1

REMOVE COVER

 

 

 

3

2

 

 

COUNTER-CLOCKWISE

 

 

OPENS CONTROL STOP

 

CLOCKWISE CLOSES

 

CONTROL STOP

 

5

 

M968699 Rev. 1.3

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Selectronic Proximity Toilet Flush Valve 1.28 & 1.6 GPF Instructions Roughing-in Dimensions Recommended Tools FigInstall the Sweat Solder Adapter Fig Install Down Tube and Vacuum Breaker FigEscutcheon and Supply Stop Fig Left or Right Hand Installation Fig Flush OUT Supply Lines FigInstall Flush Valve a & 8b Adjust Supply Stop FigHOW to Retrofit OUR Valve Fig HOW to Change the Battery FigHOW to SET Detection Range If Required Stand outside of sensor detection aeraTroubleshooting Flow Charts Selectronic Proximity Toilet Flush Valve
Related manuals
Manual 9 pages 36.61 Kb

6065.162, 6065.122, 6065.121, 6065.565, 6065.161 specifications

The American Standard values quality, durability, and innovation in its bath and toilet products. Among its notable offerings are the models 6065.565, 6065.162, 6065.121, 6065.161, and 6065.122. Each model showcases unique features and technologies that cater to diverse consumer needs.

The American Standard 6065.565 is designed with a modern aesthetic that suits any bathroom décor while ensuring functionality is not compromised. It typically features a spacious bathing well, allowing for maximum comfort. Its acrylic construction ensures a lightweight build without sacrificing durability, making it resistant to cracking and chipping. Additionally, it incorporates slip-resistant surfaces, enhancing safety for users of all ages.

Model 6065.162 offers a different take with its focus on water efficiency and sustainability. This shower model integrates advanced flow control technology, which optimizes water usage without sacrificing performance. Its ergonomic design provides a luxurious showering experience while advocating for environmental responsibility. The easy-to-clean surfaces also reduce maintenance time, allowing users to enjoy their showers without the hassle of extensive upkeep.

The 6065.121 is tailored for those seeking a modern tub design with added features. This model comes with an integrated bathing ledge, allowing for relaxation with added convenience. It is equipped with an adjustable showerhead and hand shower combination, enabling users to customize their shower experience. The tub is constructed from high-quality fiberglass, enhancing durability and insulation, ensuring water stays warm for longer periods.

Moving on to the 6065.161, this model emphasizes ergonomic design coupled with functionality. With a wide profile and deep basin, it is ideal for soaking. Advanced drainage technology ensures quick water removal, allowing for an uninterrupted bathing experience. The model’s sleek lines and minimalist appearance resonate well with contemporary design trends, making it a popular choice among homeowners.

Finally, the 6065.122 caters to those who appreciate versatility. This model can seamlessly transition from a traditional bath to a contemporary shower setup. Its quick-dry materials ensure minimal water pooling, maintaining a clean and safe environment. The design also includes built-in storage options, making it a practical solution for bathroom organization.

Together, these American Standard models exemplify the brand's commitment to innovative design and performance in the bathroom space. Whether it's prioritizing comfort, sustainability, or versatility, each model serves as a testament to American Standard’s dedication to enhancing the daily rituals of bathing.
Top Page Image Contents