PYLE Audio MN300HGA Attaching Mounting Bracket to Wall, Attaching to Wall Anchor Method

Page 8

Attaching Mounting Bracket to Wall

INSTALLATION

Note: Wall anchors, mounting screws, and spacers are in hardware package. The hardware package is provided with heater.

Attaching to Wal l Stud Method For attaching mounting bracket to wall studs

1.Drill holes at marked locations using 9/64" drill bit.

2.Place mounting bracket onto wall. Line up last hole on each end of bracket with holes drilled in wall.

3.Insert mounting screws through bracket and into wall studs.

4.Tighten screws until mounting

bracket is firmly fastened to wall studs.

Attaching to Wall Anchor Method

For attaching mounting bracket to hollow walls (wall areas between studs) or solid walls. (concrete or masonry)

1.Drill holes at marked locations using 5/16" drill bit. For solid

walls (concrete or masonry), drill at least 1" deep.

2.Fold wall anchor as shown in Figure 9 below.

Figure 9 - Folding Anchor

3.Insert wall anchor (wings first) into hole. Tap anchor flush to wall.

4.For thin walls (1/2" or less), insert red key into wall

anchor. Push red key to "pop" open anchor wings.

 

IMPORTANT: Do not ham-

mer

key! For thick walls

(over 1/

2"

thick) or solid

walls,

do not pop open wings.

Figure 10 - Popping Open Anchor Wing for Thin Walls

5.Place mounting bracket onto wall. Line up last hole on each end of bracket with wall anchors.

6.Insert mounting screws through bracket and into wall anchors.

7.Tighten screws until mounting bracket is firmly fastened to wall.

Placing Heater on Mounting Bracket

1.Locate two horizontal slots on back panel of heater (see Figure 11).

2.Place heater onto mounting bracket. Slide horizontal slots onto stand-out tabs on mounting bracket.

Figure 11 - Mounting Heater Onto Mounting Bracket

Installing Bottom Mounting Screws

1.Locate two bottom mounting holes. These holes are near bottom on back panel of heater(see Figure 12).

Figure 12 - Installing Bottom Mounting Screws

2.Mark screw locations on wall.

3.Remove heater from mounting bracket.

4.If installing bottom mounting screws into hollow or solid wall, install wall anchors. Follow steps 1 through 4 under Attaching To Wall Anchor Method. If installing bottom mounting screw into wall

stud, drill holes at marked locations using 9/64" drill bit.

5.Replace heater onto mounting bracket.

6.Place spacers between bottom mounting holes and wall anchor or drilled hole.

7. Hold spacer in place with

one

hand. With other hand, insert

mounting screw through bottom

mounting

hole and

 

spacer.

Place tip of screw in

opening

of wall anchor or drilled

hole.

 

 

8.Tighten both screws until heater is firmly secured to wall. Do not over tighten.

Note: Do not replace lower front panel at this time. Replace lower front panel after making gas connections and checking for leaks (see page 9).

8

Image 8
Contents OWNER’S Operation and Installation Manual MN300HGA MN300TGA NON-THERMOSTAT Thermostat ModelSafety Information Product Features Fresh AIR for Combustion Ventilation Producing Adequate VentilationDetermining FRESH-AIR Flow for Heater Location Unusually Tight ConstructionVentilation Air From Outdoors, Ventilation AIRInstallation Installation NeedsVentilation AIR Check GAS TypeInstallation Installing Thermostat Sensing BulbInstalling Bottom Mounting Screws Attaching Mounting Bracket to WallAttaching to Wall Anchor Method Important Do not hamConnecting to GAS Supply Important Install anNFOR Your SAFETYn Checking GAS ConnectionsThermostat Model MN300TGA Read Before LightingOperating Your Heater Thermostat Model MN300TGANON-THERMOSTAT Model MN300HGA Read Before LightingGAS to Appliance Shutting Off Burner Only pilot stays litCleaning ODS/PILOT and Burner Cleaning Burner Pilot AIR Inlet HoleCleaning Heater Cabinet Pilot Flame PatternTroubleshooting Observed Problem Possible Cause RemedyObserved Problem Possible Cause Remedy Specifications MN300TGA ODS/Pilot AssemblyIllustrated Parts Breakdown Parts List MN300TGA KEYODS/Pllot Assembly MN300HGAParts List MN300HGA KEY MN300HGA NO. Part no