Installation, Control Upgrade, Safety Precautions

INSTALLATION INSTRUCTIONS

INSTALLATION

IMPORTANT: ENSURE THAT THE APPLIANCE IS CORRECTLY ADJUSTED FOR THE GAS TYPE AND CATEGORY APPLICABLE IN THE COUNTRY OF USE. REFER TO DATABADGE AND TECHNICAL SPECIFICATIONS OF THIS BOOKLET. FOR DETAILS OF CHANGING BETWEEN GAS TYPES REFER TO SECTION 11, REPLACING PARTS.

1.CONTROL UPGRADE

1.1This stove is fitted with a control valve that can be easily upgraded to battery powered remote control. There are two versions of this control which can be obtained through your local Gazco stockist.

1.2This upgrade can be fitted before or after installation but if side clearances are limited then it will be easier to upgrade the stove before installation. Full instructions are included with the kit.

1.3STANDARD REMOTE CONTROL

This remote control can control the gas appliance after the pilot has been lit. It can turn the main burner on and regulate it from low through to high and back again. It can turn the main burner off leaving the pilot burning. GAZCO PART NUMBER 8455.

1.4THERMOSTATIC AND TIMER REMOTE CONTROL

This remote control can control the gas appliance after the pilot has been lit. In "MANUAL MODE" it can be used to turn the main burner on and manually regulate it from low through to high and back again. It can also be used to turn the main burner off leaving the pilot burning. In "AUTO MODE" it will automatically regulate the room temperature. In "TIMER MODE" it will turn the fire on and off according to a pre-set programme and automatically regulate the room temperature during two on periods. GAZCO PART NUMBER 8456.

2.SAFETY PRECAUTIONS

2.1This appliance must be installed in accordance with the rules in force, and used only in a sufficiently ventilated space. Place read these instructions before installation and use of this appliance.

2.2All the instructions must be left intact with the user.

2.3In your own interests and those of safety, this appliance must be installed by a competent person in accordance

with local and national codes of practice. Failure to install the appliance correctly could lead to prosecution.

2.4This appliance is intended for use on a governed gas installation and set to the required pressure.

2.5Keep all plastic bags away from young children.

2.6Do not place any object on or near to the stove. Allow adequate clearance above the stove. See diagram 2 Site Requirements, Appliance Location.

2.7The stove is fitted with the Gazco Flue Sure System, which will act to cut off the gas supply to the appliance in the event of incorrect operation of the flue. If the system acts to shut off the gas supply, this indicates that there is insufficient flue pull. If this occurs a minimum of 10 minutes should be

allowed before trying to relight. Continued operation of this safety device means that there may be a serious problem with the flue system; a qualified gas engineer should inspect this. DO NOT USE THE STOVE UNTIL AN ENGINEER SAYS IT IS SAFE TO DO SO.

2.8The Flue Sure System must not be tampered with. Use only genuine Gazco replacement parts when servicing the system

-refer to Servicing section, Replacing Parts.

3.INSTALLATION OF THE STOVE

FLUE PIPE INSTALLATION

3.1Open the carton and remove accessory carton and stove unit. It will now be necessary to decide upon top or rear flue exit, the stove is factory built for rear flue exit, but it may be changed to top exit by using the following method.

3.1.1Remove the flue spigot from the rear of the stove and replace with the blanking plate from the top of the stove and vice versa.

3.2Position the stove ensuring all appropriate clearances are observed. NOTE: The stove lid is loose, remove when moving the unit. Using a pencil, mark the position of the holes in the fixing brackets attached to the inside of the rear legs.

3.3Remove the stove and drill the holes using a number 12 masonry drill. Push rawlplugs into the holes and insert the woodscrews until the head is approximately 3mm proud of the hearth. Place the stove in position over the bracket so that the screw heads locate in the large part of the slot. Push the stove back so that the screw heads engage fully into the narrow part of the slot, tighten the screws if desired.

3.4Having run the gas supply to the stove, PURGE THE SUPPLY PIPE, this is essential to expel any debris that may block the gas controls. Connect the gas supply to the 8mm compression elbow at the right-hand rear corner of the stove. There is a cutout in the right-hand rear leg to enable a direct straight connection to be made to the rear of the stove. See diagram 1. A gas soundness check must be completed up to the gas inlet connection.

AR0934

3.5Check the pull of the flue system by applying a lighted smoke pellet to the flue system opening. If there is a definite flow into the chimney, proceed with the installation. If not, warm the chimney for a few minutes.

IF THERE IS STILL NO DEFINITE FLOW, THE FLUE MAY REQUIRE ATTENTION - SEEK EXPERT ADVICE

705088 specifications

Stovax 705088 is a prominent model in the realm of wood-burning stoves, recognized for its blend of modern technology and traditional aesthetics. This stove is engineered to provide efficient heating while showcasing a classic design that can complement various home interiors.

One of the primary features of the Stovax 705088 is its robust build quality, constructed from high-grade cast iron and steel. This ensures durability, allowing the stove to withstand high temperatures while providing efficient heat output. The stove features a large glass window that offers an unobstructed view of the flames, creating a warm and inviting atmosphere in any living space.

The Stovax 705088 utilizes advanced combustion technology that optimizes fuel efficiency. This technology enhances the burning process, ensuring that wood is combusted thoroughly to release maximum heat with minimal emissions. It also incorporates a clean burn system that reduces smoke production, making it an environmentally friendly option for those concerned about air quality.

Another notable characteristic is its versatility in fuel types. While primarily designed for wood burning, the Stovax 705088 can also accommodate smokeless fuels, providing homeowners with flexibility depending on their fuel availability and preferences. This adaptability not only enhances its usability but also ensures that it meets the various requirements of different regulatory zones.

The stove’s efficiency rating is particularly impressive, achieving high outputs that maximize heat generation relative to fuel consumption. This efficient energy use translates into lower heating costs, making it a practical choice for economically-minded consumers.

In terms of installation, the Stovax 705088 is designed with ease-of-use in mind. Its compact size and straight lines allow it to fit seamlessly into various spaces, whether in a traditional cottage or a modern home. Furthermore, it can be installed as a freestanding unit or as part of a fireplace insert, facilitating additional design flexibility.

In summary, the Stovax 705088 stands out in the wood-burning stove market for its sturdy construction, high efficiency, and elegant design. Its combination of advanced combustion technology and user-friendly features provides a reliable heating solution while enhancing the aesthetic appeal of any room. Whether you are looking for warmth, style, or eco-conscious performance, the Stovax 705088 is a commendable choice.