Samsung N760GR2007/SEF, N760GR2003/SEG, N760FS2023/SEG manual Undocking your Computer, Dock Change

Page 19

Front of the System

Back of the System

Docking Hook

Figure 8. Docking Sequence

To dock your computer with the power on simply place the computer on the docking hooks and press down on the area above the keyboard.

Dock Change

When the docking station is connected properly then the "Dock Change" message shows. When the "Dock Change" message disappears you may use the system. Press the system on both sides not the middle to ensure that the docking connector is completely mated to the system.

Undocking your Computer

To remove your computer from the docking station with the power off, complete the following steps.

1.Turn off the system.

2.Disconnect the AC adapter.

3.Grab the two docking release levers and pull them out until they click. The computer will pop up approximately 1cm.

4.Tilt the system up at the back.

8 Users Manual

Image 19 Contents
Macrovision Statement Safety Instructions Important Safety InformationSetting Up your System Care During Use Replacement Parts and AccessoriesBattery Disposal United States Users Regulatory Compliance StatementsFCC Part FCC part 68 applicable to products fitted with USA modems Radio Interference Regulations ICES-003 Canadian UsersDOC notice for products fitted with an IC-compliant modem Page Laser Safety Note Laser SafetyGeneral Requirements Power Cord RequirementsRequirements listed below are applicable to all countries Agency Numbers Country-Specific Power Cord Set RequirementsKeyboard Conventions Using Your DocumentationManual Documentation Conventions Information IconsCD-ROM Device Naming Convention Software User DocumentationTouchpad Conventions Introducing Your Computer Where Everything IsLCD Display PC Equipment Location Back/Left View of PC Docking Station Equipment Location Docking ConnectorDocking your Computer Docking/Undocking your ComputerDock Change Undocking your ComputerUndocking Computer Power On Installing the Battery Using Your Computer for the First TimePower Cords To attach the power cord complete the followingAC Adapter Initial computer startup To turn on the computer’s power for the first timeTurning On the Computer Turning Off Your ComputerSelect Shut down System problems requiring a computer restart Cold BootTo turn off the computer, complete the following steps Click Shut DownLCD Cleaning Using the LCD DisplayTips for Using Your Computer If you are travelling by air, follow these tips Travelling with Your ComputerAir Travel Locking your ComputerHandling Spills US Keyboard Using the KeyboardNumeric Keypad & Numlock LED Using the Numeric KeypadKey Key Function Combinations Name Using Special Function KeysUser Defined Keys Magic Keyboard Internet Quick Start ButtonMagic Keyboard Program Interface Touchpad Precautions Using the TouchpadPS/2 Mouse Drag Move Double-Click/TapArea or multiple item selection Touchpad Buttons ScrollSystem Status LEDs show the status of computer functions Reading the System Status LEDsInstalling a Modem Cable Connecting to the InternetTo connect the modem cable. follow the steps below DOS support Using the ModemPrecautions Before Use Using the Modem on a PBX systemLAN Cable Installation Back/Left Installing a LAN CablePortable LAN cable Using the Portable LAN CableConfiguring Network Environment Using the LANClick IP Address tab Click DNS Configuration tab Select Enable DNS Devices Using the Multi-Bays in the Docking StationChanging Devices Changing a 5.25 DeviceChanging 3.5 Device Changing a 3.5 DeviceDVD Notes Using the Disk DrivesUsing the Floppy Disk Drive Using the CD/DVD-ROM DriveProper CD/DVD Handling Techniques CD/DVD drive precautionsCD/DVD tray fails to slide out CD/DVD LED OnTo maintain your PC Cards, follow these guidelines Using PC CardsWorking with Pcmcia PC Cards Maintaining PC CardsInserting a PC Card Windows MeTo play an Audio CD follow the instructions below Multi Media Functions/EquipmentMedia Player Playing a Audio/Multimedia CD-ROMTo remove the CD follow the instructions below Removing the Audio CDCD LED On Movie Maker Volume ControlUsing the Keyboard Using the Volume Control IconLCD MP3 PlayerTo listen to your MP3 files simply follow the steps below Listening to a MP3 fileClick Start MP3 Loader MP3 Loader Icon will appear on Recording Voice RecorderDelete Recording Follow these rules for charging your battery Using the BatteryCharging the Battery Approximate charging times for the Li-Ion battery areGeneral Environment Increasing Battery LifeAdjust LCD Brightness Power ManagementCalibration Notes Safely Using the BatteryBattery Calibration If you replace your battery with a new oneTo install the battery pack, follow the steps below Removing the BatteryInstalling the Battery Monitoring the Battery ChargePower Meter Battery WarningsStarting System Setup Using System SetupNavigation Key Function Boot Device Priority field enables Changing Booting PriorityPress in the Boot Device Priority field Creating a Password Using System SecuritySystem Passwords If You Forget Your PasswordTo delete the password follow the steps below Deleting a PasswordSelect Exit Saving Changes, press Bios Interface Using Power Management OptionsIntel SpeedStepTM Task Bar Interface Standby vs. Hibernation Basic Power Management SchemesChanging Devices Hibernate Mode Power Management or Manual Method Sleep key is assigned to the + key combination Advanced Power Management SchemesWhen Do you wish to enable large disk support Y/N...? shows Installing a New HDDInstalling/Reinstalling a HDD Using Fdisk UtilityFormatting the HDD ReInstalling Windows and Device DriversTo format the HDD complete the following Adjusting the LCD Display Video Features and ConfigurationCRT Only Resolution and Color DepthDual Monitor LCD & CRT Dual View Using the LCD and CRT as 1 Display Configuring Display FeaturesSelecting a Monitor Type Click Change. The Update Device Driver Wizard screen appears Changing Color Depth and ResolutionDisplay Properties Window To enable TV-out Using the TV-Out PortClick the Start Settings Control Panel Select Start Settings Control panel Using Duo View ModeSetting Duo View Mode To set Duo View mode on your systemDual View Display Menu Uncheck Extend my Windows desktop onto this monitorBefore You Install Memory Using OptionsMemory Module To install a memory module Installing a Memory ModuleMemory Module Precautions Installing a Memory Module Battery power seems to run out faster than expected TroubleshootingOperating Problems Computer does nothing when you turn it onNo sound Video ProblemsCan not use the ZV card Cannot toggle between CRT and LCD while playing the 3D game Modem ProblemsSelect Settings External monitor displays flashes or wavesATX3&W When using a PBX phone system I cant dial on my modemWindows Me Modem Driver ReInstallation Driver Problems / Driver ReInstallationModem Driver ReInstallation Selecting a Country Confirming ReInstallation of the Modem DriverIncorrect Country Selection Command mode Modem CommandsWhat are AT Commands? Before Using AT CommandsDisplay the result value Using AT CommandsConnection may be lost depending on the server ATO Basic AT CommandsATX4 Click the Device Manager tab Windows Me LAN Driver ReInstallationLAN Driver ReInstallation Start Settings Control PanelSound Driver ReInstallation Windows Me Sound Driver ReInstallationCheck Specify a location and type D\Audio\Winme Click Settings Advanced in Display Properties Windows Me ReinstallationChanging the Video Driver Gives the specifications for your slim notebook computer SpecificationsCD-ROM AbbreviationsPcmcia Voltage collector current Universal serial busVolt Voltage alternating currentGlossary COM port DMA direct memory accessCardBus Cmos memoryIRQ interrupt request line Floppy diskHard drive AddressOperating system RAM random access memoryMB megabyte MegabitShadow RAM ResolutionROM read-only memory Sector
Related manuals
Manual 113 pages 22.24 Kb Manual 115 pages 46.55 Kb