Samsung VR10M703PW9/WA manual Troubleshooting, ENGLISH-34, POWERbot cannot find

Page 34

Troubleshooting

Symptom

Checklist

 

ffCheck if the emergency switch is on.

 

ffCheck if all the icons are displayed on the display panel.

 

ffCheck if the POWERbot's battery is depleted.

The POWERbot is not

––When "Lo" is displayed, place the POWERbot on the docking

station to charge it.

working at all.

––When the battery indicator blinks, manually place the POWERbot

 

 

on the docking station to charge. (Only SR10M701✴✴✴ series)

 

ffReplace the batteries (AAA type) if the remote control is not

 

working.

 

ffWhen "Lo" is displayed on the display panel, place the POWERbot

 

on the docking station to charge it.

 

ffWhen the battery indicator blinks, manually place the POWERbot

The POWERbot has stopped

on the docking station to charge. (Only SR10M701✴✴✴ series)

ffWhen POWERbot is immobilized by an obstacle such as a cord,

during cleaning.

threshold etc, pick it up and move it away from the obstacle.

 

 

––If any fabric or string is caught in a drive wheel, turn off the

 

emergency switch and remove the fabric or string before using

 

it again.

 

fIf the "Filter inspection indicator" is on, turn off the emergency

 

switch and clean the dustbin.

 

ffWhen there's too much dust in the dustbin, suction power may get

 

weakened. Turn off the emergency switch and empty the dustbin.

Suction power is weak.

fIf the intake (on bottom of POWERbot) is blocked by foreign

 

matter, turn off the emergency switch and remove foreign matter

 

from the intake.

 

ffWhen noise suddenly increase, turn off the emergency switch and

 

empty the dustbin.

 

ffCheck if there's a power failure or whether the power plug is

 

unplugged.

The POWERbot cannot find

ffRemove any obstacles around the docking station that may

the docking station.

prevent POWERbot from returning to the docking station.

 

ffWhen there's foreign matter on the charge pins, charging can be

 

affected. Clean the foreign matter off the pins.

 

ffCheck if the docking station is installed along the grain of wooden

 

floors or tiles.

The POWERbot suddenly

ffThe POWERbot may clean in a diagonal direction if it is moving

cleans diagonally.

to another area using the shortest route. It may also move at a

diagonal if it made contact with an obstacles at that angle, if it

 

 

was charged at the docking station at an angle, or if the grain of

 

the wooden/tile floor skewed is in that direction.

 

fIf you point the red light directly at POWERbot, it may not move in

 

desired direction.

Point cleaning is not working.

––Point the red light on the floor within 0.5 m of POWERbot.

 

✻✻Do not use point cleaning in direct sunlight, under bright light, or

 

on dark floors.

ENGLISH-34

Image 34
Contents POWERbot Using the remote control ENGLISH-02Other Symbols Used Safety informationENGLISH-03 General Important Safety InstructionsENGLISH-04 ENGLISH-05 ENGLISH-06 FfPlease prevent any risk of electric shock or fireENGLISH-07 Installation ENGLISH-08Accessories ENGLISH-09Smart Charging ChargingENGLISH-10 SR10M701 Series Check the installation status of the docking station whenManually charge the POWERbot when SR10M70 / SR2070 SeriesStarting Auto clean mode Using POWERbotTurning the power on/off Using Spot clean modeENGLISH-13 Repeat clean Auto clean Spot clean Manual cleanENGLISH-14 About the boundary markers ENGLISH-15Using the remote control ENGLISH-16Suction power Power / Recharging / Start/StopCleaning modes Additional functionOperating distance of the remote control Manual clean mode & Direction controlPoint cleaning ENGLISH-18Bottom Name of each partTop Display panelSR20M70 series SR10M702 / SR10M703 seriesENGLISH-20 Setting the schedule Setting time/scheduleSetting the time Type, B Type Only Auto clean mode can be scheduledType, D Type Only Auto clean mode can be scheduled ENGLISH-22ENGLISH-23 Cleaning the sensors and the camera Cleaning and maintainingCleaning the dustbin ENGLISH-24Cleaning the Driving wheel Cleaning the brush and Auto shutter toolENGLISH-25 Samsung Connect App Setting up the wireless routerENGLISH-26 Downloading the Samsung Connect App Setting up a Samsung accountENGLISH-27 Adding a device to the Samsung Connect APP ENGLISH-28Using the Samsung Connect APP Software UpdateENGLISH-29 Charging UsingCleaning and maintenance ENGLISH-30About the IrDA sensor About the batteryENGLISH-31 Information codes ENGLISH-32Main PCB needs to be checked POWERbot is caught, stuck or trapped whileMoving around ENGLISH-33POWERbot cannot find TroubleshootingENGLISH-34 ENGLISH-35 WorkOpen Source Announcement ENGLISH-36SR10M70 series SpecificationsENGLISH-37 Memo ENGLISH-38ENGLISH-39 India
Related manuals
Manual 40 pages 24.02 Kb Manual 40 pages 60.55 Kb Manual 184 pages 2.99 Kb Manual 184 pages 42.75 Kb