Electrical Connections, Planning | Draper 220V SLX instruction

Installation/Operating Instructions

220V SL & SLX Scissor Lift Video Projector Lift by Draper

These Installation/Operating Instructions are available in the ofﬁcial language of the country where you purchase the product. Please contact your distributor to request a copy.

Vous pourriez demander les instructions d’installation et d’opération traduises dans la langue ofﬁcielle du pays ou vous achetez le produit. Veuillez demander à votre distributeur.

Die Gebrauchsanweisung für Installation und Konstruktion sind in der ofﬁziellen Sprache des Landes, indem Sie das Produkt gekauft haben, vorhanden. Fragen Sie die jeweilige Verkaufs-Abteilung.

Caution:

➀Read instructions completely before proceeding.

➁ Test lift prior to installation.

➂ Follow instructions carefully. Installation contrary to instructions invalidates warranty.

➃ Do not obstruct operation of Scissor Lift with ﬁ ngers or any object. Serious injury or damage could result.

➄ Scissor Lift is designed to accommodate ceiling suspended equipment. Equipment should not be allowed to rest on optional ceiling closure during operation. (Refer to section titled “Installing Projector.”)

➅ Entire bottom of unit must be unobstructed to permit proper operation. Sufﬁ cient clearance must be allowed below projector or optional ceiling closure: see chart on page 4.

➆ Unit must be installed level (use a carpenter’s level).

➇ Unit operates on 220V, 50 Hz. AC current.

Note: Unit has been thoroughly inspected and tested at factory and found to be operating properly prior to shipment.

➂Fastening methods must be suitable for mounting surface, and securely anchored so that vibration or abusive pulling on unit will not weaken

installation.

➃Unit should be level, with weight shared more or less equally by all four

threaded mounting rods.

➄Bottom of unit must be unobstructed after installation. Sufﬁ cient clearance must be allowed below projector or optional ceiling closure: 4' for Model

SL4, 5' for Model SL5, etc.; 11' for Model SLX11, 12' for Model SLX12, etc.

➅Do not use unit to support adjacent ceiling, light ﬁ xtures, etc.

➆Do not complete the ceiling below unit until electrical connections have

been completed and unit has been operated successfully.

➇We recommend that safety cables be attached to the Scissor Lift for added security (a sound installation practice with overhead equipment).

Electrical Connections

Unit operates on 220V AC, 50 Hz. current. Removing the top cover of the unit and opening the electrical box exposes terminals for ﬁ eld connections. Unit is shipped with internal wiring complete. Wire to connect unit to power supply should be furnished by installer. Connections should be made in accordance with wiring diagram, and wiring should comply with national and local electrical codes. All operating switches should be “off” before power is connected.

Scissor Lift should be operated and checked prior to installing projector and/or optional ceiling closure.

Standard switch shown below comes with 22.86 meters of cable and should be plugged in to box on front of top pan of lift to control lift.

Planning

➀Based on screen location and projector speciﬁ cations, determine proper position for projector installation.

➁Conﬁ rm that there is adequate space for installation and operation. Minimum clearance above ceiling level varies according to Scissor Lift

model, plus height of projector, optional mounting bracket, optional ceiling closure, and optional plenum rated housing.

➂Arrange to provide service access to the unit.

OFF OFF

DOWN

As Soon As Scissor Lift Arrives

Operation

➀ Open carton and inspect for damage.

When unit is ﬁ rst operated, be cautious! If unit fails to operate when toggle

➁ Locate the following parts:

switch is ﬂ ipped “down”, return switch to “off” and recheck electrical

A. The unit itself

connections before proceeding. Cycle unit down and up several times to

B. Controls

conﬁ rm satisfactory operation.

C. Any optional equipment: plenum housing, closure panel, ceiling ﬁ nish kit

Standard Single Station Control (CE Approved)—One, 12V toggle switch:

or decorative cover (all ship in separate cartons).

moving 3-position toggle switch to “down” position will start lift down. Moving

➂ Test lift prior to installation.

toggle switch to “up” will start lift up. When lift is in “show” position, travel will

Hanging Unit

automatically be stopped by factory set limit switches. Whenever switch is

The Scissor Lift may be installed in a variety of ways; recessed above the

placed in center “off” position, operation will stop. One, 12V key switch will

ceiling, or suspended below the ceiling. The lift should be supported by four

lower lift from “show” to “service” position.

½" threaded mounting rods. If ceiling recessed, the entire unit (including

Video Interface Control (CE Approved)—This optional 12V control device

the projector) should set approximately 1½" above the ﬁ nished ceiling in its

allows the Scissor Lift switch to control the operation of a Draper motorized

“stored” position. The threaded rods should pass through the corner mounting

projection screen via a relay.

ﬂ anges and be secured by nuts above and below. Use a thread locking

Multiple Station Control (Not CE Approved)—Optional, moves lift from

compound such as Loctite® #242 (provided). The unit should then be guy

wired or blocked to prevent swinging.

“stored” to “show” position only. Each switching station has a 3-button switch

with “up”, “down”, and “off” buttons. Lift starts up or down when appropriate

All installations should observe the following guidelines:

button is pressed, and may be stopped by pressing “off” button. Factory set

➀ Access from above the unit, with enough clearance to remove the top

cover, should be provided in case service is required. If installing above a

limit switches stop lift automatically when projector is in “show” position.

hard ceiling, optional Draper Access Panels are available to allow access to

Key Operated Switch (Not CE Approved)—If ordered, a single station, key-

the unit.

operated three position (up/off/down) switch is available. Multiple Station Con-

➁ Installer must ensure that all fasteners and supports are of adequate

trol required for this option. Moves lift from “stored” to “show” positions only.

strength to securely support Scissor Lift and projector.

Infrared or Radio Frequency Remote Control (CE Approved)—If ordered, a

three-button transmitter is provided, with “up”, “down”, and “stop” buttons. Unit

starts up or down when appropriate button is pressed, and may be stopped by

pressing “off” button. Factory set limit switches stop unit automatically when

projector is in “show” position. Only controls "show" and "stored" positions.

Loctite® is a registered trademark of Henkel Corporation.

If you encounter any difﬁculties installing or servicing your Scissor Lift, call your

Form ScissorLift_220VInst08

Printed in U.S.A.

dealer or Draper, Inc. in Spiceland, Indiana, 765-987-7999; or fax 765-987-7142.

220V SLX, 220V SL specifications

The Draper 220V SL and 220V SLX models represent the pinnacle of innovation in the realm of electric lifting and handling equipment. Designed for professionals who require reliability and efficiency, these products are perfect for various applications, including industrial, agricultural, and construction settings.

One of the main features of the Draper 220V SL is its robust lifting capacity, allowing it to handle loads of up to 220 kg with ease. This capability is complemented by a lift height of 3 meters, making it suitable for a wide range of tasks such as hoisting, moving, and positioning heavy materials or equipment. The SLX model takes this a step further by offering advanced lifting options, enhancing its versatility and performance.

Both the SL and SLX boast a strong, durable construction. They are built with high-quality materials designed to withstand the rigors of continuous use in demanding environments. The heavy-duty steel frame ensures stability and longevity, while the powder-coated finish provides added protection against corrosion and wear.

When it comes to safety, Draper prioritizes user protection. The 220V models are equipped with various safety features, including emergency stop buttons, automatic overload protection, and secure locking mechanisms. These elements work together to reduce the risk of accidents and ensure that the equipment can be operated with peace of mind.

In terms of technology, the 220V SL and SLX leverage advanced electric motor systems that provide smooth and efficient operation. These models are designed to minimize energy consumption while delivering high performance, thereby promoting sustainability in daily operations. The user-friendly control panel offers intuitive access to all functions, making it easy to operate the equipment even for those who are less experienced.

Another significant characteristic is the portability of these models. The Draper 220V SL and SLX are designed with mobility in mind, featuring sturdy wheels and a lightweight design that allow for easy transport across job sites. This portability ensures that users can adapt quickly to different tasks and locations without compromising on performance.

In summary, the Draper 220V SL and 220V SLX models are powerful, versatile, and user-friendly electric lifts that combine advanced technology with robust construction. Whether for industrial tasks, agricultural needs, or construction projects, these machines are crafted to deliver efficiency and safety, making them essential tools for any professional.