|
|
|
|
|
|
| Features in |
|
|
| 25 | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR | Module | Level | Description | AR44xS/ AR450S | AR7x5 | AR750S |
| Rapier i |
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR00011311 | IPsec | 4 | In output of the commands show ipsec policy and show ipsec policy | Y | - | Y |
| Y | Y | - |
| - | - | - | - |
|
|
| sabundle, the value for the number of bytes currently used by each SA bundle |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| was sometimes truncated. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| This issue has been resolved, and both commands now display the correct |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| number. As part of this, output of the command show ipsec policy has been |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| modified so that the expiry limits in bytes and in seconds display on separate |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| lines. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Also, if the expirykbytes parameter of the command create or set ipsec |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| bundlespecification was given a value higher than 4193280, the router or |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| switch instead used a lower value. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| This issue has been resolved. If you specify a value above 4193280, the router or |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| switch now displays a warning message and sets the expiry limit to 4193280 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| kbytes. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR00012270 | Remote Telnet | 4 | The “?” help description for the enable command stated that the parameter | Y | - | Y |
| Y | - | - |
| - | - | - | - |
|
|
| rtelnet would “Disable the use of remote telnet to control an asyn port”. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| This issue has been resolved. The query now states that the command enable |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| rtelnet enables remote telnet. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CR00012755 | Install, | 4 | If the local command show config dynamic was entered as a | - | - | - |
| Y | Y | Y |
| Y | - | - | - |
| Stacking |
| command, the switch gave an incorrect error message. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| This issue has been resolved. If you attempt to direct show config dynamic to |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| a host, the switch now responds with the message “Command is local, do not |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| use host direction”. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Version