DeWalt DWX723, DWX724 instruction manual DW7231 Universal Miter Saw Mounting Method

Page 6

English

5.Repeat procedure on the other end of the bracket.

6.Move the 2 x 4 to the other side of the saw to hold the other end of the saw up in order to access the saw base.

7.Feed carriage bolts through the other bracket and the base of the saw as before. Ensure both brackets are parallel to each other.

8.To place the saw onto the stand, grasp and lift saw by mounting bracket assembly by the release levers. These levers do not lock the saw laterally in place but merely serve as a means of mounting the saw to the beam.

FIG. 6

9. Approach the beam with saw/bracket

FIG. 7

assembly tilting toward your body slightly.

 

Engage the concave front lip of the

 

mounting bracket with rounded edge of

 

beam. One of the brackets must engage

I

the locator clip (I) to prohibit lateral

movement of the saw during use.

 

10. When front edge of the beam and locking locator clip are engaged, a slight downward pivot will allow secure engagement of the release levers to the back of the beam. Rock the saw gently on the brackets to verify locking in position.

11. Adjust the saw position as necessary to have the blade perpendicular to the beam when in the 0 degree miter position.

12. Tighten the four nuts holding the saw to the brackets securely.

DW7231 Universal Miter Saw Mounting Method (Fig. 1, 7–9)

WARNING: To reduce the risk of injury, turn unit off, disconnect machine from power source before assembling the miter saw to the miter saw stand. An accidental start-up can cause injury.

WARNING: Stability Hazard. You must use the plywood mounting method described in the following instructions when mounting a miter saw not manufactured by DEWALT to this miter saw stand. WARNING: To reduce the risk of personal injury, be sure the miter saw is fully anchored on the stand.

WARNING: For your own safety, read and understand the miter saw instruction manual before using. Failure to heed these warnings may result in personal injury and serious damage to the miter saw and the accessory.

NOTE: If you do not have a DEWALT miter saw, you must use 3/4" (19 mm) plywood to mount your miter saw.

The plywood must be a minimum of 4" (101.6 mm) wider than the largest width of the miter saw base. The plywood should be at least as deep as the smallest depth of the miter saw base or a minimum of 16" (406.4 mm) if miter saw base is smaller. Ensure the plywood is square.

1.Once the Plywood size has been determined, drill 3/8" (9.5 mm) holes 1" (25.5 mm) from the front corners of plywood, 15" (355 mm) apart and 1" (25.5 mm) from the sides.

2.Place DW7231 mounting brackets on the stand:

a.Grasp and squeeze release levers (G).

b.Engage the concave front lip of the mounting bracket with rounded front edge of beam. One of the mounting brackets must be engaged in the locator clip (I) to prohibit lateral movement of the saw during use.

4

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Heavy-Duty Miter Saw Stand trabajo pesado English DWX723/DWX724 Miter Saw Stands Components ListGeneral Safety Instructions for Miter Saw Stands Definitions Safety GuidelinesCarton Contents Miter Saw Stand with Folding Legs DWX723/DWX724DW7232 Work Piece Support and Length Adjustable Length Extension Arm FigPreparation Fig Stops FigDW7231 Hardware Selection Chart DW7231 Dewalt Miter Saw Mounting MethodDW7231 Universal Miter Saw Mounting Method Carry Strap Locking Locator Clip Fig AccessoriesThree Year Limited Warranty Removing the SawDAY Money Back Guarantee Français Établis de scie à onglet DWX723/DWX724 DescriptionOutils nécessaires Définitions lignes directrices en Matière de sécuritéContenu du carton Description FigSupport de pièce et butées de longueur DW7232 à Préparation FigMéthode d’installation de La scie à onglet Dewalt DW7231 Rallonge réglage FigTableau DE Sélection DE Matériel DW7231 Côté gauche Côté droitFrançais Courroie de transport Agrafe de fixation du positionneur FigPoignée de transport Fig AccessoiresRetrait de la scie RéparationsService D’ENTRETIEN Gratuit DE 1 AN Garantie DE Remboursement DE 90 JoursEspañol Contenido de la caja Definiciones Normas de seguridadBase para ingleteadora DWX723/DWX724 Herramientas requeridasDW7232 Soporte para pieza a trabajar y topes de longitud Fig Preparación FigBrazo de extensión de longitud ajustable Fig Método de montaje para ingleteadora Dewalt DW7231DW7231 Gráfico Para Selección DE Accesorios DE Montaje Lado izquierdo Lado derechoDW7231 Método de montaje para ingleteadora Anchura DE LA Sierra Para retirar la sierra Correa para transportePinza de seguridad del localizador Fig Asa FigPóliza de Garantía ExcepcionesGarantía limitada de tres años Servicio Gratuito DE 1 AÑOGarantía DE Reembolso DE Dinero DE 90 Días Herramientas Electricas Page

DWX724, DW7231, DWX723 specifications

DeWalt, a leading manufacturer of power tools and accessories, offers a range of high-quality cutting equipment designed for professional use. Among its acclaimed products are the DWX724, DWX723, and DW7231 miter saw stands, each boasting distinct features and technologies to enhance performance and convenience on the job site.

The DeWalt DWX724 is a versatile and portable miter saw stand, crafted to accommodate most miter saws available in the market. One of its key features is the telescoping arm, allowing for longer materials to be supported, making it easier to work with larger pieces of wood. This stand also folds up easily for transportation and storage, with a lightweight aluminum construction that ensures reliability without adding unnecessary weight. Additionally, the DWX724 has integrated wheels for effortless maneuverability and setup, providing mobility on job sites.

Next, the DeWalt DWX723 is designed with durability and stability in mind. This miter saw stand offers a robust build quality, utilizing heavy-duty materials that withstand the rigors of professional use. Like the DWX724, it features extendable arms that can support up to 16 feet of material, enabling users to tackle large projects efficiently. The stand includes fast and easy setup mechanisms, allowing professionals to get to work swiftly. Furthermore, the DWX723 is compatible with a wide range of miter saws, reinforcing its versatility.

The DeWalt DW7231 is an accessory that enhances the functionality of the DW723 stand. This tool is specifically designed for the DW723 miter saw stand, allowing users to seamlessly connect and detach their saws. One of the most notable aspects of the DW7231 is its quick-release mounting brackets, which facilitate rapid saw changes without complicated setups. This feature supports efficient workflow and minimizes downtime during projects. This convenient addition exemplifies DeWalt's commitment to innovation in tool design, prioritizing user needs and safety.

In summary, the DeWalt DWX724, DWX723, and DW7231 miter saw stands are engineered to provide a blend of flexibility, durability, and efficiency. Whether you're a contractor or a DIY enthusiast, these stands offer essential features that contribute to a more effective and productive cutting experience in various environments. DeWalt continues to be a trusted name through their commitment to quality and their understanding of professional tool demands.
Top Page Image Contents